Grizzly H8259 owner manual Assembly Test Run, To assemble the lathe, To test run the machine

Page 14

Assembly

 

Test Run

 

 

 

 

 

 

Before use, the tool rest must be moved out of its shipping position and the quill handwheel knob must be attached.

To assemble the lathe:

1.Loosen the release lever and rotate the tool rest base away from the lathe bed.

2.Loosen the tool rest lock handle and rotate the tool rest so that it is positioned parallel to the lathe bed (Figure 6).

3.Tighten the tool rest lock handle.

Tool Rest

Tool Rest

Lock Handle

 

 

Release

Tool Rest

 

 

Lever

Base

 

 

 

 

 

 

 

Figure 6. Tool rest positioned.

4.

Secure

the

crank

to

the quill

handwheel

 

(Figure 7).

 

 

 

 

 

 

 

 

 

Quill

 

 

 

 

 

 

Handwheel

 

Crank

 

 

 

 

 

Figure 7. Quill handwheel crank installed.

-12-

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the following:

1)The motor powers up and runs correctly.

2)The safety paddle switch works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 26. If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Make sure that you have read the safety instructions at the beginning of this manual and that the machine is setup properly.

2.Connect the machine to the power source.

3.Turn the machine ON. Make sure that your hand stays poised over the switch in case you need to quickly turn the machine OFF.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power before investigating or correcting potential problems.

4.Turn the machine OFF.

5.Remove the safety key and attempt to turn the machine ON.

—If the machine starts, stop it and disconnect it from power. The switch disabling feature is not working. This safety feature must work properly before proceeding. Call Tech Support for help.

—If the machine does not start, the switch disabling feature is working.

H8259 10" x 18" Benchtop Lathe

Image 14
Contents Model H8259 Page Table of Contents Contact Info IntroductionForeword H8259 10 x 18 Benchtop Lathe H8259 10 x 18 Benchtop Lathe Identification H8259 10 x 18 Benchtop Lathe H8259 10 x 18 Benchtop Lathe Additional Safety for Wood Lathes Circuit Requirements 110V OperationBox Contents Figure Qty SetupSet Up Safety Unpacking InventoryG7895-Grizzly Citrus Degreaser Clean UpSite Considerations To test run the machine Assembly Test RunTo assemble the lathe Changing Speeds Operation SafetyOperations To change speedsOpen the side and rear access covers Figure To position the tailstock along the bed Adjusting Tailstock Adjusting Tool RestTo adjust the tool rest To position the tool rest base along the bedTo install the spur center Installing/Removing Spur CenterInstalling/Removing Live Center To install the live centerTo remove the live center Removing/Installing FaceplateTo install faceplate To remove faceplateSelecting Turning Tools GougeTo set up a spindle turning operation Spindle TurningFaceplate Turning To mount your workpiece to the faceplateSanding/Finishing To mount your workpiece to a backing blockH7828-Tool Table Plus AccessoriesG1194-3-Jaw Chuck G1082-4-Jaw ChuckSchedule MaintenanceCleaning Unpainted Cast IronTo remove the old belt To install new beltChanging Belt Service TroubleshootingSymptom Possible Cause Possible Solution H8259 Wiring Diagram Motor connections H8259 10 x 18 Benchtop LatheMain Breakdown Main Breakdown Parts List Description101 103 104 102 105 106 Page Page Warranty and Returns