Grizzly G0658, G0657 owner manual Test Run, To test run the machine

Page 18

Test Run

Once the setup is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the following:

1)The motor powers up and runs correctly, and

2)the safety disabling mechanism on the switch works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 30.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Connect the machine to the power source.

4.Verify that the machine is operating correctly by turning the machine ON.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

5.Turn the machine OFF.

6.Remove the switch disabling key, as shown in Figure 12.

Figure 12. Removing switch key from paddle

switch.

7.Try to turn the start the machine with the paddle switch.

—If the machine does not start, the switch disabling feature is working as designed.

—If the machine starts, immediately stop the machine. The switch disabling feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

-16-	G0657/G0658 Benchtop Lathe

Image 18

Contents Benchtop Lathe Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info G0657/G0658 Identification #.% $!4 THERH3PECIFICATIONS $%,$88 %!69 $549 %.#4/0 ,!4% AIN 3PECIFICATIONS #ONSTRUCTION !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety for Wood Lathes Circuit Requirements 110V OperationBox Contents Figure Qty SetupSetup Safety Inventory Additional Contents G0658 only QtySite Considerations Clean UpG2544-Solvent Cleaner & Degreaser G0657 G0658Mounting Setup To install the outboard turning attachment Model G0658 onlyTo prepare the lathe Test Run To test run the machineOperation Safety Basic Controls OperationsTailstock Controls G0657/G0658 Benchtop Lathe Changing Speed Ranges To change speedsAdjusting Tailstock Adjusting Tool Rest To position the tailstock along the bedTo position the tool rest base along the bed To install the spur center Installing/Removing Spur CenterInstalling/Removing Live Center To install the live centerTo remove the live center Removing/Installing FaceplateTo install the faceplate To remove the faceplateSelecting Turning Tools GougeOutboard Turning G0658 Only To place the tool rest on the outboard turning attachmentTo set up a spindle turning operation Spindle TurningFaceplate Turning To mount your workpiece to the faceplateSanding/Finishing To mount your workpiece to a backing blockH7828-Tool Table Plus AccessoriesG1194-3-Jaw Chuck G1082-4-Jaw ChuckSchedule MaintenanceCleaning Unpainted Cast IronService TroubleshootingSymptom Possible Cause Possible Solution To install new belt Changing BeltTo remove the old belt Motor Service G0657/G0658 Wiring Diagram 6!#G0657 Main Breakdown G0657 Main Breakdown Parts List DescriptionG0657 Main Breakdown Parts List Contd G0657 Labels Breakdown & Parts List G0658 Main Breakdown G0658 Main Breakdown Parts List G0658 Main Breakdown Parts List contd G0658 Labels Breakdown & Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%