Grizzly G0657, G0658 owner manual Sanding/Finishing, To mount your workpiece to a backing block

Page 29

NOTICE: Only use tap screws or wood screws with non-tapered heads (Figure 39) to attach the faceplate to the workpiece. Do NOT use drywall screws or screws with tapered heads because these can split the faceplate, or the screws may snap off during operation.

<DD9769

Figure 39. Correct and incorrect screw types for

mounting faceplate to workpiece.

To mount your workpiece to a backing block:

1.Make the backing block (Figure 40) from a piece of scrap wood that is flat on both sides.

Sanding/Finishing

After turning, the workpiece can be sanded, as shown in Figure 41, and finished (in the same manner) before removing it from the lathe.

Figure 41. Typical sanding operation.

Backing Block

HVcYeVeZg

Ldg`e^ZXZ

Wrapping the sandpa- per completely around the workpiece will pull your hands into the mov- ing workpiece and may cause injury. Never wrap sandpaper completely around the workpiece!

Figure 40. Example of mounting faceplate to a

backing block.

2.Locate and mark the center of both the workpiece and the backing block.

3.Drill a 14" diameter hole through the center of the backing block.

4.Glue the center of the backing block to the center of the workpiece (look through the drilled hole to line up centers), clamp the backing block to the workpiece, and wait for the glue to cure according to the manufactur- er’s recommendation.

G0657/G0658 Benchtop Lathe

Whenever sanding or finishing, move the tool rest holder out of the way to increase personal safety and gain adequate working room.

-27-

Image 29
Contents Benchtop Lathe Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview G0657/G0658 Identification #.% $!4 THERH3PECIFICATIONS $%,$88 %!69 $549 %.#4/0 ,!4% AIN 3PECIFICATIONS #ONSTRUCTION  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety for Wood Lathes 110V Operation Circuit RequirementsSetup Safety Inventory SetupBox Contents Figure Qty Additional Contents G0658 only QtyG2544-Solvent Cleaner & Degreaser Clean UpSite Considerations G0657 G0658Mounting To prepare the lathe SetupTo install the outboard turning attachment Model G0658 only To test run the machine Test RunOperations Operation Safety Basic ControlsTailstock Controls G0657/G0658 Benchtop Lathe To change speeds Changing Speed RangesTo position the tool rest base along the bed Adjusting Tailstock Adjusting Tool RestTo position the tailstock along the bed Installing/Removing Live Center Installing/Removing Spur CenterTo install the spur center To install the live centerTo install the faceplate Removing/Installing FaceplateTo remove the live center To remove the faceplateGouge Selecting Turning ToolsTo place the tool rest on the outboard turning attachment Outboard Turning G0658 OnlySpindle Turning To set up a spindle turning operationTo mount your workpiece to the faceplate Faceplate TurningTo mount your workpiece to a backing block Sanding/FinishingG1194-3-Jaw Chuck AccessoriesH7828-Tool Table Plus G1082-4-Jaw ChuckCleaning MaintenanceSchedule Unpainted Cast IronTroubleshooting ServiceSymptom Possible Cause Possible Solution To remove the old belt To install new beltChanging Belt Motor Service 6!# G0657/G0658 Wiring DiagramG0657 Main Breakdown Description G0657 Main Breakdown Parts ListG0657 Main Breakdown Parts List Contd G0657 Labels Breakdown & Parts List G0658 Main Breakdown G0658 Main Breakdown Parts List G0658 Main Breakdown Parts List contd G0658 Labels Breakdown & Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%