Grizzly G0658 Removing/Installing Faceplate, To remove the live center, To remove the faceplate

Page 24

To remove the live center:

1.Loosen the quill lock handle (if locked) approximately half a turn counterclockwise.

2.Turn the quill handwheel counterclockwise until the tailstock quill bottoms out, causing the live center to be forced out of the quill.

The tailstock quill lock handle must always be locked down while the lathe is in use. The workpiece can be thrown from the lathe if this step is not observed. Also, the tailstock quill should not protrude from the tailstock housing more than 2'' or the quill will not be supported enough. Failure to follow these warnings may result in personal injury.

Removing/Installing

Faceplate

These instructions cover removing and installing the faceplate. To mount a workpiece to your face- plate, refer to Faceplate Turning on Page 26.

To remove the faceplate:

1.DISCONNECT lathe from power!

2.Hold the headstock spindle wheel securely while turning the faceplate counterclockwise until it is removed. If the spur center is installed, it will be removed during this pro- cess.

-22-

Faceplate

Headstock

Spindle wheel

Figure 26. Removing faceplate.

To install the faceplate:

1.DISCONNECT lathe from power!

2.Thread faceplate onto spindle shaft until it is secure against the shoulder on the spindle shaft.

G0657/G0658 Benchtop Lathe

Image 24

Contents Benchtop Lathe Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info G0657/G0658 Identification #.% $!4 THERH3PECIFICATIONS $%,$88 %!69 $549 %.#4/0 ,!4% AIN 3PECIFICATIONS #ONSTRUCTION !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety for Wood Lathes Circuit Requirements 110V OperationSetup Setup Safety InventoryBox Contents Figure Qty Additional Contents G0658 only QtyClean Up G2544-Solvent Cleaner & DegreaserSite Considerations G0657 G0658Mounting Setup To install the outboard turning attachment Model G0658 onlyTo prepare the lathe Test Run To test run the machineOperation Safety Basic Controls OperationsTailstock Controls G0657/G0658 Benchtop Lathe Changing Speed Ranges To change speedsAdjusting Tailstock Adjusting Tool Rest To position the tailstock along the bedTo position the tool rest base along the bed Installing/Removing Spur Center Installing/Removing Live CenterTo install the spur center To install the live centerRemoving/Installing Faceplate To install the faceplateTo remove the live center To remove the faceplateSelecting Turning Tools GougeOutboard Turning G0658 Only To place the tool rest on the outboard turning attachmentTo set up a spindle turning operation Spindle TurningFaceplate Turning To mount your workpiece to the faceplateSanding/Finishing To mount your workpiece to a backing blockAccessories G1194-3-Jaw ChuckH7828-Tool Table Plus G1082-4-Jaw ChuckMaintenance CleaningSchedule Unpainted Cast IronService TroubleshootingSymptom Possible Cause Possible Solution To install new belt Changing BeltTo remove the old belt Motor Service G0657/G0658 Wiring Diagram 6!#G0657 Main Breakdown G0657 Main Breakdown Parts List DescriptionG0657 Main Breakdown Parts List Contd G0657 Labels Breakdown & Parts List G0658 Main Breakdown G0658 Main Breakdown Parts List G0658 Main Breakdown Parts List contd G0658 Labels Breakdown & Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%