Jet Tools JWL-1642EVS-2 Sanding and Finishing, Face Plate and Bowl Turning, Mounting Stock

Page 17

Sanding and Finishing

Leaving clean cuts will reduce the amount of sanding required. Adjust the lathe to a finishing speed, and begin with fine sandpaper (120 grit or finer). Coarser sandpaper will leave deep scratches that are difficult to remove, and dull crisp details. Fold the sandpaper into a pad; do not wrap sandpaper around your fingers or the workpiece.

To apply a finish, the workpiece can be left on the lathe. Turn the lathe off and use a brush, or cloth to apply the finish. Remove excess finish before restarting lathe. Allow it to dry and sand again with 320 or 400 grit sandpaper. Apply additional coats of finish and buff.

Face Plate and Bowl Turning

Faceplate turning is normally done on the inboard side of the headstock over the bed; see Figure 20.You must move the headstock to the end of the lathe bed for larger workpieces.

Mounting Stock

Use of a faceplate is the most common method for holding a block of wood for turning bowls, and plates, see Figure 21.

1.Select stock at least 1/8" to 1/4" larger than the dimension on the desired finished workpiece.

2.True one surface of workpiece for mounting against the faceplate. It is best to leave extra stock against the faceplate that can be cut off when the workpiece is finished.

3.Using the faceplate as a template, mark the location of the mounting holes, and drill pilot holes of the appropriate size. If the mounting screws on the faceplate interfere with the workpiece, a waste block can be mounted to the faceplate and then the waste block mounted to the workpiece by gluing or screwing, see Figure 21.

4.Both waste block and workpiece should have good flat surfaces.

5.Push in the spindle lock and thread faceplate and workpiece onto spindle. Tighten setscrews in faceplate when secure.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Part Number M-708359 WMH Tool GroupWarranty and Service Page Speed Recommendations Volts7 Total Length of Cord in Feet Volt Operation Model JWL-1642EVS onlyVolt Operation Model JWL-1642EVS-2 only Introduction Table of Contents JWL-1642EVS-2 SpecificationsInput Power 115V Only Input Power 230V Only Assembly Contents of the Shipping ContainersUnpacking and Clean-Up Tool Basket Stand ShelfGuard Controls and FeaturesCenter’s shaft. Unscrew the tip and change as needed Lathe Tools Disconnect the machine from the power sourceSpeed Change Mounting Workpiece Between Centers Roughing Out Stock SelectionCuts CovesParting BeadsMounting Stock Sanding and FinishingFace Plate and Bowl Turning Wood Selection Face Plate or ChuckChecks and Cracks DistortionTo Shape the Outside of a Bowl Sanding and Finishing a Bowl To Shape the Interior of a BowlChanging the Belt and Bearings Adjusting the Clamping MechanismProblem Possible Cause Solution TroubleshootingStand and Bed Assembly Index Part Description Size Qty Headstock Assembly JWL1642-MFC JWL1642-147 Wiring Diagram for JWL-1642EVS Wiring Diagram for JWL-1642EVS-2 Indexer Positions How to use the chartPage Vantage Drive Elgin, Illinois Phone
Related manuals
Manual 27 pages 56.8 Kb

JWL-1642EVS-2, JWL-1642EVS specifications

The Jet Tools JWL-1642EVS and JWL-1642EVS-2 are standout lathes in the realm of woodturning, designed for both novice and seasoned woodworkers. These lathes offer unmatched versatility and precision, making them ideal for a wide variety of turning projects, from simple spindles to complex bowls.

One of the most notable features of the JWL-1642EVS is its powerful 1.5 HP motor that delivers excellent torque across a wide range of RPMs. This enhanced performance allows users to work with various wood species while maintaining smooth operation, a critical factor for achieving a high-quality finish. The electronic variable speed (EVS) control system provides convenient adjustments, allowing artisans to select the optimal speed for their specific turning needs. With a speed range from 40 to 3,600 RPM, craftspeople can effortlessly switch between fine detail work and aggressive stock removal.

The lathe's robust design is complemented by a cast iron bed that minimizes vibrations and ensures stability during operation. This construction not only enhances durability but also contributes to precise results, allowing users to create intricate designs without worrying about inconsistencies in the finish. Additionally, the JWL-1642EVS-2 variant offers an even larger capacity, with an impressive 16-inch swing over the bed and 42-inch length, accommodating larger workpieces.

Furthermore, both models feature a convenient electronic spindle lock, making the process of changing chucks and accessories quick and efficient. The adjustable swivel headstock allows for greater flexibility in accessing various angles, providing users with more control and comfort during operation.

Safety is also a priority in the design of the JWL-1642EVS and JWL-1642EVS-2, with features such as a safety restart switch, ensuring that the lathe cannot restart unexpectedly after a power interruption. Easy-to-read digital readouts for speed settings further enhance user experience by allowing for precise monitoring while turning.

Overall, the Jet Tools JWL-1642EVS and JWL-1642EVS-2 combine advanced technology, durable construction, and user-friendly features, making them indispensable tools for any woodturner looking to expand their craft and achieve professional-quality results. Whether you’re creating functional items or artistic pieces, these lathes empower users to elevate their woodturning endeavors.
Top Page Image Contents