Jet Tools JWL-1642EVS-2 operating instructions Mounting Workpiece Between Centers

Page 14

Mounting Workpiece Between Centers

Spindle turning takes place between the centers of the lathe. It requires a spur center in the headstock and a live center in the tailstock.

1.With a ruler locate and mark the center on each end by going corner to corner, see Figure 13. Accuracy is not critical on full rounds but extremely important on stock where square sections are to remain. Put a dimple in each end of the stock with an awl, or nail.

2.Extremely hard woods may require kerfs cut into the spur drive end of stock, see Figure 13. You may need to drive the spur center into the stock with a wood mallet. Note: Never drive stock onto spur while it is mounted in the lathe spindle.

3.Install workpiece by inserting the attached spur center into the spindle taper on the headstock.

4.Bring tailstock into position, lock it to the bed, and advance quill with the handwheel in order to seat the live center into the workpiece. Lock the quill in place. Make sure the live center point is centered on your mark.

5.Move tool rest into position. It should be parallel to workpiece, approximately at the centerline and approximately 1/8" from the closest part of the workpiece. Lock tool rest body and tool rest in place.

6.Rotate workpiece by hand to check for proper clearance from tool rest. Note: You may want to trim off the corners of a square workpiece to make turning a little easier, see Figure 14.

7.Start lathe at the lowest speed and bring it up to the appropriate RPM for the size of stock, see Figure 7 page 10.

The position of the tool rest can be varied to suit the work and operator. After you become experienced with setting the tool rest changing the position will become second nature for the workpiece and comfort of the user.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents WMH Tool Group Part Number M-708359Warranty and Service Page Speed Recommendations Volt Operation Model JWL-1642EVS only Volts7 Total Length of Cord in FeetVolt Operation Model JWL-1642EVS-2 only Introduction Table of Contents JWL-1642EVS-2 SpecificationsInput Power 115V Only Input Power 230V Only Assembly Contents of the Shipping ContainersUnpacking and Clean-Up Stand Shelf Tool BasketControls and Features GuardCenter’s shaft. Unscrew the tip and change as needed Lathe Tools Disconnect the machine from the power sourceSpeed Change Mounting Workpiece Between Centers Stock Selection Roughing OutParting CovesCuts BeadsMounting Stock Sanding and FinishingFace Plate and Bowl Turning Checks and Cracks Face Plate or ChuckWood Selection DistortionTo Shape the Outside of a Bowl To Shape the Interior of a Bowl Sanding and Finishing a BowlAdjusting the Clamping Mechanism Changing the Belt and BearingsTroubleshooting Problem Possible Cause SolutionStand and Bed Assembly Index Part Description Size Qty Headstock Assembly JWL1642-MFC JWL1642-147 Wiring Diagram for JWL-1642EVS Wiring Diagram for JWL-1642EVS-2 How to use the chart Indexer PositionsPage Vantage Drive Elgin, Illinois Phone
Related manuals
Manual 27 pages 56.8 Kb

JWL-1642EVS-2, JWL-1642EVS specifications

The Jet Tools JWL-1642EVS and JWL-1642EVS-2 are standout lathes in the realm of woodturning, designed for both novice and seasoned woodworkers. These lathes offer unmatched versatility and precision, making them ideal for a wide variety of turning projects, from simple spindles to complex bowls.

One of the most notable features of the JWL-1642EVS is its powerful 1.5 HP motor that delivers excellent torque across a wide range of RPMs. This enhanced performance allows users to work with various wood species while maintaining smooth operation, a critical factor for achieving a high-quality finish. The electronic variable speed (EVS) control system provides convenient adjustments, allowing artisans to select the optimal speed for their specific turning needs. With a speed range from 40 to 3,600 RPM, craftspeople can effortlessly switch between fine detail work and aggressive stock removal.

The lathe's robust design is complemented by a cast iron bed that minimizes vibrations and ensures stability during operation. This construction not only enhances durability but also contributes to precise results, allowing users to create intricate designs without worrying about inconsistencies in the finish. Additionally, the JWL-1642EVS-2 variant offers an even larger capacity, with an impressive 16-inch swing over the bed and 42-inch length, accommodating larger workpieces.

Furthermore, both models feature a convenient electronic spindle lock, making the process of changing chucks and accessories quick and efficient. The adjustable swivel headstock allows for greater flexibility in accessing various angles, providing users with more control and comfort during operation.

Safety is also a priority in the design of the JWL-1642EVS and JWL-1642EVS-2, with features such as a safety restart switch, ensuring that the lathe cannot restart unexpectedly after a power interruption. Easy-to-read digital readouts for speed settings further enhance user experience by allowing for precise monitoring while turning.

Overall, the Jet Tools JWL-1642EVS and JWL-1642EVS-2 combine advanced technology, durable construction, and user-friendly features, making them indispensable tools for any woodturner looking to expand their craft and achieve professional-quality results. Whether you’re creating functional items or artistic pieces, these lathes empower users to elevate their woodturning endeavors.
Top Page Image Contents