Jet Tools JWL-1642EVS-2 operating instructions To Shape the Outside of a Bowl

Page 19

To Shape the Outside of a Bowl

1.Odd shaped burls, crotches and other irregular shaped blanks require special preparation before mounting in a chuck, or onto a faceplate. Remove the bark, if there is any, from what appears to be the center of the top of workpiece.

2.Drive the spur center into the top of workpiece with a wood mallet.

3.Slip the spur center into the headstock taper and bring the tailstock, with a live center, into position. Lock the tailstock to the bed and advance the spindle in order to seat the cup center into the workpiece, see Figure

22.Tighten the quill lock.

4.Position the tool support just below the centerline and about 1/4" from the workpiece. Note: For larger outboard turning, an optional outboard turning stand is used to place the tool support, see your JET distributor.

5.Turn the workpiece by hand to ensure proper clearance.

6.Start the lathe at the lowest speed and bring it up to the maximum safe speed for the size of work to be turned, see Figure 7 on page

10.If the machine starts to vibrate, lower the speed until the vibration stops.

7.Rough out the outside of the bowl with the 1/2" deep fluted bowl gouge, holding the tool firmly against your hip. For best control, use your whole body to move the gouge through the workpiece.

8.As the bowl takes shape, work on the bottom (tailstock end) to accommodate attaching a faceplate, see Figure 22.

9.Turn a short tenon (about 1/8" long) the size of the hole in the faceplate, see Figure 22.This will allow centering the workpiece when the faceplate is attached. Note: If you plan to use a chuck, turn a tenon of appropriate length and diameter to fit your chuck.

10.Stop the lathe, remove the workpiece and attach the faceplate, or chuck.

11.Finish turning the outside of the bowl with a 1/2" or 3/8" bowl gouge. Leave additional material at the base of the bowl for support while turning the interior. This will be removed later.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Part Number M-708359 WMH Tool GroupWarranty and Service Page Speed Recommendations Volts7 Total Length of Cord in Feet Volt Operation Model JWL-1642EVS onlyVolt Operation Model JWL-1642EVS-2 only Introduction Table of Contents Input Power 115V Only Input Power 230V Only SpecificationsJWL-1642EVS-2 Unpacking and Clean-Up Contents of the Shipping ContainersAssembly Tool Basket Stand ShelfGuard Controls and FeaturesCenter’s shaft. Unscrew the tip and change as needed Speed Change Disconnect the machine from the power sourceLathe Tools Mounting Workpiece Between Centers Roughing Out Stock SelectionBeads CovesCuts PartingFace Plate and Bowl Turning Sanding and FinishingMounting Stock Distortion Face Plate or ChuckWood Selection Checks and CracksTo Shape the Outside of a Bowl Sanding and Finishing a Bowl To Shape the Interior of a BowlChanging the Belt and Bearings Adjusting the Clamping MechanismProblem Possible Cause Solution TroubleshootingStand and Bed Assembly Index Part Description Size Qty Headstock Assembly JWL1642-MFC JWL1642-147 Wiring Diagram for JWL-1642EVS Wiring Diagram for JWL-1642EVS-2 Indexer Positions How to use the chartPage Vantage Drive Elgin, Illinois Phone
Related manuals
Manual 27 pages 56.8 Kb

JWL-1642EVS-2, JWL-1642EVS specifications

The Jet Tools JWL-1642EVS and JWL-1642EVS-2 are standout lathes in the realm of woodturning, designed for both novice and seasoned woodworkers. These lathes offer unmatched versatility and precision, making them ideal for a wide variety of turning projects, from simple spindles to complex bowls.

One of the most notable features of the JWL-1642EVS is its powerful 1.5 HP motor that delivers excellent torque across a wide range of RPMs. This enhanced performance allows users to work with various wood species while maintaining smooth operation, a critical factor for achieving a high-quality finish. The electronic variable speed (EVS) control system provides convenient adjustments, allowing artisans to select the optimal speed for their specific turning needs. With a speed range from 40 to 3,600 RPM, craftspeople can effortlessly switch between fine detail work and aggressive stock removal.

The lathe's robust design is complemented by a cast iron bed that minimizes vibrations and ensures stability during operation. This construction not only enhances durability but also contributes to precise results, allowing users to create intricate designs without worrying about inconsistencies in the finish. Additionally, the JWL-1642EVS-2 variant offers an even larger capacity, with an impressive 16-inch swing over the bed and 42-inch length, accommodating larger workpieces.

Furthermore, both models feature a convenient electronic spindle lock, making the process of changing chucks and accessories quick and efficient. The adjustable swivel headstock allows for greater flexibility in accessing various angles, providing users with more control and comfort during operation.

Safety is also a priority in the design of the JWL-1642EVS and JWL-1642EVS-2, with features such as a safety restart switch, ensuring that the lathe cannot restart unexpectedly after a power interruption. Easy-to-read digital readouts for speed settings further enhance user experience by allowing for precise monitoring while turning.

Overall, the Jet Tools JWL-1642EVS and JWL-1642EVS-2 combine advanced technology, durable construction, and user-friendly features, making them indispensable tools for any woodturner looking to expand their craft and achieve professional-quality results. Whether you’re creating functional items or artistic pieces, these lathes empower users to elevate their woodturning endeavors.
Top Page Image Contents