Wolfcraft 3408 manual General Safety Instructions for Power Tools

Page 3

SAFETY INSTRUCTIONS

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS

READ ALL SAFETY INSTRUCTIONS BEFORE USING Read the owner's manual carefully. Learn its applications and limitations as well as the specific potential hazards.

GROUND ALL TOOLS (UNLESS DOUBLE INSULATED) If tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire. NEVER connect the green wire to a live terminal.

KEEP AWAY FROM HAZARDOUS MATERIALS

Normal sparking of the motor could ignite fumes, flammable liquids, or combustibles.

PROTECT YOURSELF AGAINST PERSONAL INJURY DO NOT operate any tool while under the influence of drugs, alcohol, or any medication.

DRESS FOR SAFETY

Do not wear loose clothing, gloves, neckties, or jewelry, as these items can get caught and draw you into moving parts. ALWAYS wear non-slip footwear. Tie back long hair. Roll long sleeves above the elbow.

WEAR SAFETY GOGGLES

Wear safety goggles (must comply with ANSI Z87.1) at ALL times. Also, use face or dust mask if cutting operation is dusty, and use ear protectors (plugs or muffs) during extended periods of operation.

AVOID ACCIDENTAL STARTING

Make sure all switches are in "OFF" position before plugging in.

NEVER STAND ON TOOL

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. DO NOT store materials above or near the tool making it necessary to stand on the tool to reach them.

PROTECT AND USE SUITABLE CORDS

NEVER carry tool by cord or yank it to disconnect from receptacle. Protect cord from heat, oil, and sharp edges. For outdoor operation, use extension cords intended for outdoor use.

AVOID A DANGEROUS ENVIRONMENT

DO NOT use power tools in damp or wet locations or expose them to rain. Keep work area well lit and provide an adequate surrounding work space.

CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

NEVER LEAVE TOOL RUNNING UNATTENDED Turn power off. Do not leave tool until it comes to a complete stop.

KEEP HANDS AWAY FROM CUTTING AREA

DISCONNECT TOOLS BEFORE SERVICING When changing bits, make sure tool is unplugged.

KEEP GUARDS IN PLACE

Be sure guards are in working order, properly adjusted, and aligned.

KEEP WORK AREA CLEAN

ALWAYS keep your work area clean, uncluttered, and well lit. DO NOT work on or place router table legs on floor surfaces that are slippery from sawdust, oil, water, or wax.

DO NOT FORCE THE TOOL

Do not force tool or attachment to do a job for which it was not designed. It will do the job better and more safely at the rate for which it was designed.

USE CLAMPS OR A VISE TO HOLD WORK WHEN PRACTICAL

Using clamps or a vise to hold work is safer than using your hand. It also frees both hands to operate the tool.

DO NOT OVERREACH

Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

USE RECOMMENDED ACCESSORIES

Consult this manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards.

REMOVE ADJUSTING KEYS AND WRENCHES

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

ENSURE SAFETY OF OTHERS

Keep visitors and children a safe distance away from the work area, especially when operating a power tool. Visitors should wear the same safety equipment as the operator.

SAVE THESE INSTRUCTIONS

3

Image 3
Contents Wolfcraft Warranty Table of ContentsGeneral Safety Instructions for Power Tools Safety InstructionsUnpacking and Checking Contents Features and SpecificationsIntroduction Package Contents & Hardware Legend Package Contents & Hardware Legend Assembly Tools RequiredAssemble Drill Press Stand Page Standard Mounting Drill MountingHorizontal Mounting Operating InstructionsKEY Description QTY Repair Parts 3408 Universal Drill Press StandGarantie / Garantía Table DES Matieres / ÍndiceConsignes DE SECURITE/INSTRUCCIONES DE Seguridad Mode Dutilisation Générale Pour LES Outils ÉlectriqueIntroduction / Introducción Article Description QTÉ Artículo Descripción Cant Descripción Cant Article Description QTÉOutils requis/Herramientas necesarias Assemblage / ArmadoFigura Montage DE LA Perceuse / Montaje DEL Taladro Montage Horizontal Montaje Horizontal Utilisation / OperaciónDescripción Pièces DE Réparation / Piezas DE ReparaciónWolfcraft Name Product Registration CardWolfcraft