Bosch Power Tools 3365 manual Assembly, Chip Extraction

Page 7

Assembly

CHIP EXTRACTION

The planer comes with two chip exhaust ports, which may be used with a chip bag (Fig.2) or a shop vacuum and vacuum connector (Fig.3) to keep your work environment cleaner. The chip bag or vacuum connector may be attached to either end of the exhaust port.

Moving the port selector lever to position 1 (towards front of tool) discharges chips to the left, while position 2 (towards rear of tool) discharges chips to the right (Fig. 1)

PLANER BLADES

The planer blades are sharp ! WARNING and fragile and must be

handled carefully to avoid injury to the user or damage to the blades.

The planer blades have two cutting edges, and may be reversed when one of the

FIG. 2

CHIP BAG

FIG. 3

EXHAUST

PORTS

cutting edges becomes dull or chipped.

Do not attempt to sharpen or use resharpened used blades of any kind. Use only blades designated for use with this model, because other blades will cause vibration, decrease perfomance and may not clamp securely in blade holder.

REVERSING OR REPLACING BLADES

VACUUM

CONNECTOR

(OPTIONAL)

To reverse or replace the blade, loosen the clamping screws with blade wrench. With the screws loosened, slide the blade lengthwise out of the cutter drum, taking care to keep your fingers away from the sharp edges of the blade (Fig. 4).

A piece of wood may be used for this purpose. If the blade is gummed and difficult to remove, you may clean the blade with mineral spirits, lacquer thinner or alcohol.

Clean all surfaces before reinstalling the new blade, as this will ensure an accurate blade setting and proper tool performance.

BLADE ALIGNMENT

To ensure an even cut, it is important that the blade is adjusted so that it aligns with the outside edge of the front and rear shoes. This alignment can be done as follows: place a straight edge or a piece of wood along the outside surface of the front shoe and rear shoe, then slide the planer blade to just contact the straight edge or wood (Fig.5).

2.5MM BLADE

WRENCH

CUTTER

DRUM

FIG. 4

CLAMPING

SCREW

CUTTER

DRUM

CLAMPING

SCREW BLADE

BLADE

WRENCH

Make sure the blade sits correctly in the holder groove of the cutter drum.

You may then tighten the clamping screws which secure the blade and your planer is ready for use.

FIG. 5

STRAIGHT

EDGE

-7-

Image 7
Contents Importante Work Area Power Tool Safety RulesService Safety Rules for PlanersPage Symbols Planer Functional Description and SpecificationsChip Extraction AssemblyOperating Instructions Trigger ON/OFF SwitchDeluxe Angle Fence Accessories MaintenanceSécurité des personnes Règles de Sécurité GénéralesAire de travail Sécurité électriqueRéparation Consignes de sécurité pour les rabotsLe plomb provenant des peintures à base de plomb Symboles Rabot Description fonctionnelle et spécificationsAlignement DU FER AssemblageÉvacuation DES Copeaux Fers DE RabotInterrupteur MARCHE/ARRÊT Gâchette Consignes de fonctionnementRabotage Butée DE Profondeur Pour Feuillures Guide Inclinable DE LuxeCourroie DE Transmission Nettoyage AccessoiresService EntretienSeguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para cepillos mecánicosPage De Ni-Cd SímbolosCepillo mecánico Descripción funcional y especificacionesInversión O Cambio DE LAS Cuchillas EnsamblajeExtracción DE Virutas Cuchillas DEL Cepillo MecánicoAcción DE Acepillado Instrucciones de funcionamientoAjuste DE LA Profundidad DE Corte Polea Impulsada TOPE-GUÍA Angular DE LujoTope DE Profundidad DE Rebajado Correa DE TransmisiónAccesorios MantenimientoLimpieza Page Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools