Craftsman 315.21222 Towasherwith, Doubledflats Bladebolt Outerbladewasher Withdoubledflats

Page 14

LOWERARROW

BLADEGUARD

PHILLIPS

SCREW

BLADE

BOLTCOVER

TO

LOOSEN

FLAT(S)

ON SPINDLE

INNERBLADE

TOWASHERWITH

DOUBLE"D"FLATS

BLADEBOLT

BLADE

OUTERBLADEWASHER

 

WITHDOUBLE"D"FLATS

Fig. ll

Depress the spindle lock button and rotate the blade bolt until the spindle locks. See Figure 12.

Using the blade wrench provided, loosen and remove the blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen.

Remove outer blade washer. Do not remove inner blade washer.

SPINDLE

LOCKBUTTON

Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade.

A WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 11.

A CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

Replace outer blade washer. The double "D" flats on the blade washers align with the flats on the spindle.

Depress spindle lock button and replace blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

Tighten blade bolt securely.

Remove the blade wrench and store it in a safe place for future use.

Replace the lower blade guard and blade bolt cover.

Retighten phillips screw securing blade bolt cover. Tighten screw securely. See Figure 11.

A WARNING: To prevent damage to the spindle lock, always allow motor to come to a complete stop before engaging spindle lock. Make sure the spindle lock button is not engaged before reconnecting saw into power source.

Your compound miter saw has been adjusted at the factory for making very accurate cuts. However, some of the components might have been jarred out of alignment during shipping. Also, over a period of time, readjustment will probably become necessary due to wear. After unpacking your saw, check the following adjustments before you begin using saw. Make any readjustments that are necessary and periodically

Fig. 12 check the parts alignment to make sure that your saw is cutting accurately.

WARNING: Your saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. Disconnecting your saw will prevent accidental starting that could cause serious injury.

14

Image 14
Contents 12 in. Compound Miter SAW Double Insulated Full ONE Year Warranty Double Insulation Symbolmeaning Safety Alert SymbolRemove Adjusting Keys Read ALL InstructionsInspect Extension Cords Periodi Never USE in AN Explosive Atmo Before Making a CUT, be Sure ALL Adjustments are SecureMake Sure the Miter Table and SAW Bevel Cut Rules For Safe OperationArea has Ample CrosscutKetscrew Miterlockhandle SawbladeDustguide FramingsquareAwarning / ADVERTENClA Cutting Capacities Bladeguard Sawarm Switch TriggerAMP Motor Know Your Compound Miter SAWCarrying Handle Switchtrigger Spindle Lockbutton Trigger LockPadlock Switch Carryinglockpin Handle SAW ARM MiterlockMounting Holes Electric BrakeFence Electrical ConnectionSee Figures 10, 11, Exhaust Port Dustguide To Install BladeLoosen Tighten Control Miter ARM Lockhandle Dust Guide Lower Bladeguard Phillips Screw Bolt LowerbladeSpindle Lockbutton TowasherwithDoubledflats Bladebolt Outerbladewasher Withdoubledflats Squaring the Miter Table To the Fence Cutting a Slot in the Zero Clearance Throat PlateFraming Fence See Figures 13See Figures 17 Head ScrewsSquaring the SAW Blade to Fence MiterSee Figures Mm Socket HeadSquaring the Blade to Miter Table CombinationBevel Pivot Adjustment Bevellock Knob Positivestop Adjustment for 45ANGLESPivot Adjustments Travel Pivot Adjustment Depth Stop AdjustmentsTo Crosscut with Your Miter SAW ApplicationsCutting with Your Compound Miter SAW Use only for the purposes listed belowClamp Leftsiderightside Leftht Indicatorindicator PointpointTo Bevel CUT with Your Miter SAW Bevel CUTBevelcut Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Compound Mitercut ClampLongworkpiece Workpiecesupports WorkpieceSee. Figures 29Support Long Workpieces Pitch of Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters NumberofsidesLaying Molding Flat on Miter Table Cutting Crown MoldingCeiling Wide Board Right Cutting Warped MaterialClamping Wide Workpieces Extension Cords GeneralLubrication Dustbag Exhaustport Brush ReplacementBrush Embly Brush CAP Assembly Dust BAG Table Extensions Clamp Extensionrod Bracket Small Screw Support Wingscrew Clamp AssemblyWork Clamp Extension Clamp Bracket Screw Holesfor Clamp ExtensionrodClampworkpieceto the Fence Fig Clamping Workpiece to the FenceKnob Clamp Extensionrod Screws Clampsupport Clampworkpieceto the SawtableFigureA Craftsman Compound Miter SAW- Model NumberKEY Part NO. Number Description QuanT633 Parts List for Figure B Description QuanFigureC Description Quan See Back page for Parts Ordering InstructionsPart STD31551111 p.m. CST =800-366=7278 Days Week

315.21222 specifications

The Craftsman 315.21222 is a versatile and powerful tool that stands out in the world of portable power equipment. Designed for both professionals and DIY enthusiasts, this product encapsulates precision, durability, and efficiency. It is most recognized as a portable air compressor, which is particularly favored for its functionality and robustness.

One of the main features of the Craftsman 315.21222 is its impressive air tank capacity, which ensures prolonged use without frequent refills. With a sizable tank, users can complete tasks that require sustained air pressure, making it ideal for various applications like inflating tires, powering pneumatic tools, and operating airbrushes. The quick recovery time of the compressor allows users to tackle jobs more efficiently, minimizing downtime.

Another noteworthy characteristic is its powerful motor, which delivers robust performance. It operates at a high PSI level, ensuring that it can handle demanding applications such as framing, roofing, and even spray painting. This feature makes the Craftsman 315.21222 an exceptional choice for professionals in the construction and automotive industries, as well as for home users embarking on renovation projects.

The technology employed in the Craftsman 315.21222 focuses on user comfort and safety. It comes equipped with an easy-to-read pressure gauge, allowing users to monitor the air pressure effectively. The compressor also features a thermal overload protector that prevents the motor from overheating during extended use, thereby enhancing the tool's longevity and reliability.

The design of the Craftsman 315.21222 is another factor contributing to its appeal. It features a compact and portable configuration, complete with sturdy wheels and a handle, making it easy to transport from one job site to another. This portability is essential for contractors who need to take their tools on the road or for hobbyists who require equipment that can be easily stored.

Lastly, the Craftsman brand is synonymous with quality and innovation, and the 315.21222 lives up to this reputation. The manufacturer provides excellent customer support and a warranty, which adds to the peace of mind for users. Whether for casual hobby use or serious professional tasks, the Craftsman 315.21222 is a reliable and efficient choice that meets a wide array of air compression needs.