Craftsman 315.21222 owner manual General, Lubrication, Extension Cords

Page 27

,_ WARNING:Whenservicing,useonlyidentical Craftsmanreplacementparts.Useof anyother

partmaycreateahazardorcauseproduct damage.

GENERAL

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

,i_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating

oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.

It has been found that electric tools are subject to accelerated wear and possible premature failure when they are used on fiberglass boats, sports cars, wallboard, spackling compounds, or plaster. The chips and grindings from these materials are highly abrasive to electric tool parts such as bearings,

brushes, commutators, etc. Consequently, it is not recommended that this tool be used for extended

work on any fiberglass material, wallboard, spackling compounds, or plaster. During any use on these materials it is extremely important that the tool is cleaned frequently by blowing with an air jet.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.

EXTENSION CORDS

The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent tool overheating, use an extension cord that is heavy enough to carry the current the tool will draw.

Awire gage size (A.W.G.) of at least 14 is recom- mended for an extension cord 25 feet or less in

length. When working outdoors, use an extension

cord that is suitable for outdoor use. The cord'sjacket will be marked WA.

A CAUTION: Keep extension cords away from the cutting area and position the cord so that it will not get caught on lumber, tools, etc., during cutting operation.

A WARNING: Check extension cords before each use. If damaged, replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 12 in. Compound Miter SAW Double Insulated Full ONE Year Warranty Read ALL Instructions Symbolmeaning Safety Alert SymbolRemove Adjusting Keys Double InsulationInspect Extension Cords Periodi Before Making a CUT, be Sure ALL Adjustments are Secure Make Sure the Miter Table and SAWNever USE in AN Explosive Atmo Crosscut Rules For Safe OperationArea has Ample Bevel CutKetscrew Framingsquare SawbladeDustguide MiterlockhandleAwarning / ADVERTENClA Know Your Compound Miter SAW Bladeguard Sawarm Switch TriggerAMP Motor Cutting CapacitiesCarryinglockpin Handle SAW ARM Miterlock Switchtrigger Spindle Lockbutton Trigger LockPadlock Switch Carrying HandleElectrical Connection Electric BrakeFence Mounting HolesLower Bladeguard Phillips Screw Bolt Lowerblade Exhaust Port Dustguide To Install BladeLoosen Tighten Control Miter ARM Lockhandle Dust Guide See Figures 10, 11,Towasherwith Doubledflats Bladebolt Outerbladewasher WithdoubledflatsSpindle Lockbutton See Figures 13 Cutting a Slot in the Zero Clearance Throat PlateFraming Fence Squaring the Miter Table To the FenceMiter Head ScrewsSquaring the SAW Blade to Fence See Figures 17Combination Mm Socket HeadSquaring the Blade to Miter Table See FiguresDepth Stop Adjustments Bevellock Knob Positivestop Adjustment for 45ANGLESPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentUse only for the purposes listed below ApplicationsCutting with Your Compound Miter SAW To Crosscut with Your Miter SAWBevel CUT Leftsiderightside Leftht Indicatorindicator PointpointTo Bevel CUT with Your Miter SAW ClampCompound Miter CUT Bevelcut ClampCompound Mitercut Clamp To Make a Compound CUT with Your Miter SAWWorkpieceSee. Figures 29 Support Long WorkpiecesLongworkpiece Workpiecesupports Numberofsides COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Pitch of SideCutting Crown Molding CeilingLaying Molding Flat on Miter Table Cutting Warped Material Clamping Wide WorkpiecesWide Board Right General LubricationExtension Cords Brush Replacement Brush Embly Brush CAP Assembly Dust BAGDustbag Exhaustport Table Extensions Extension Clamp Bracket Screw Holesfor Clamp Extensionrod Clamp AssemblyWork Clamp Clamp Extensionrod Bracket Small Screw Support WingscrewClampsupport Clampworkpieceto the Sawtable Clamping Workpiece to the FenceKnob Clamp Extensionrod Screws Clampworkpieceto the Fence FigCraftsman Compound Miter SAW- Model Number FigureADescription Quan KEY Part NO. NumberT633 Description Quan Parts List for Figure BFigureC STD315511 See Back page for Parts Ordering InstructionsPart Description Quan=800-366=7278 Days Week 11 p.m. CST

315.21222 specifications

The Craftsman 315.21222 is a versatile and powerful tool that stands out in the world of portable power equipment. Designed for both professionals and DIY enthusiasts, this product encapsulates precision, durability, and efficiency. It is most recognized as a portable air compressor, which is particularly favored for its functionality and robustness.

One of the main features of the Craftsman 315.21222 is its impressive air tank capacity, which ensures prolonged use without frequent refills. With a sizable tank, users can complete tasks that require sustained air pressure, making it ideal for various applications like inflating tires, powering pneumatic tools, and operating airbrushes. The quick recovery time of the compressor allows users to tackle jobs more efficiently, minimizing downtime.

Another noteworthy characteristic is its powerful motor, which delivers robust performance. It operates at a high PSI level, ensuring that it can handle demanding applications such as framing, roofing, and even spray painting. This feature makes the Craftsman 315.21222 an exceptional choice for professionals in the construction and automotive industries, as well as for home users embarking on renovation projects.

The technology employed in the Craftsman 315.21222 focuses on user comfort and safety. It comes equipped with an easy-to-read pressure gauge, allowing users to monitor the air pressure effectively. The compressor also features a thermal overload protector that prevents the motor from overheating during extended use, thereby enhancing the tool's longevity and reliability.

The design of the Craftsman 315.21222 is another factor contributing to its appeal. It features a compact and portable configuration, complete with sturdy wheels and a handle, making it easy to transport from one job site to another. This portability is essential for contractors who need to take their tools on the road or for hobbyists who require equipment that can be easily stored.

Lastly, the Craftsman brand is synonymous with quality and innovation, and the 315.21222 lives up to this reputation. The manufacturer provides excellent customer support and a warranty, which adds to the peace of mind for users. Whether for casual hobby use or serious professional tasks, the Craftsman 315.21222 is a reliable and efficient choice that meets a wide array of air compression needs.
Top Page Image Contents