Craftsman 315.21222 owner manual Applications, Cutting with Your Compound Miter SAW, Crosscutting

Page 19

DEPTHSTOP

ADJUSTMENT

SCREW

BEVEL

LOCKKNOB

POSITIVE

MITER

STOPADJUSTMENT

TABLE

SCREWFOR 0° ANGLES LOCKNUT(S)

Fig. 25

and raised by turning the screw clockwise. Lower the blade into the zero clearance throat plate of the miter table. Check blade clearance and maximum cutting distance (distance from fence where blade enters) to front of miter table slot.

•Readjust if necessary.

WARNING: Do not start your compound miter saw without checking for interference between

the blade and the miter table support. Damage could result to the blade if it strikes the miter

table support during operation of the saw.

•Tighten the hex nut with a 17 mm wrench or adjustable wrench.

•To prevent the depth stop adjustment screw from turning while tightening the hex nut, carefully hold it with the hex key while tightening the hex nut.

APPLICATIONS

(Use only for the purposes listed below)

•Cross cutting wood and plastic.

•Cross cutting miters, joints, etc. for picture frames, moldings, door casings, and fine joinery.

Note: The blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your nearest Sears store.

WARNING: Before starting any cutting operation, clamp, bolt or nail your compound

miter saw to a workbench. Never operate your miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.

CUTTING WITH YOUR COMPOUND

MITER SAW

,& WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury.

CROSSCUTTING

See Figure 26.

A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the zero degree position. Miter crosscuts are made with the miter table set at some angle other than zero.

TO CROSSCUT WITH YOUR MITER

SAW:

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter

lock handle approximately one-half turn to the left to loosen.

•Press the miter lock plate down with your thumb and hold.

•Rotate the control arm until the pointer aligns with the desired angle on the miter scale.

•Release the miter lock plate.

Note: You can quickly locate 0°, 15°, 22-1/2 °, 31.62 °, and 45 ° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame.

•Tighten the miter lock handle securely.

WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 12 in. Compound Miter SAW Double Insulated Full ONE Year Warranty Read ALL Instructions Symbolmeaning Safety Alert SymbolRemove Adjusting Keys Double InsulationInspect Extension Cords Periodi Make Sure the Miter Table and SAW Before Making a CUT, be Sure ALL Adjustments are SecureNever USE in AN Explosive Atmo Crosscut Rules For Safe OperationArea has Ample Bevel CutKetscrew Framingsquare SawbladeDustguide MiterlockhandleAwarning / ADVERTENClA Know Your Compound Miter SAW Bladeguard Sawarm Switch TriggerAMP Motor Cutting CapacitiesCarryinglockpin Handle SAW ARM Miterlock Switchtrigger Spindle Lockbutton Trigger LockPadlock Switch Carrying HandleElectrical Connection Electric BrakeFence Mounting HolesLower Bladeguard Phillips Screw Bolt Lowerblade Exhaust Port Dustguide To Install BladeLoosen Tighten Control Miter ARM Lockhandle Dust Guide See Figures 10, 11,Doubledflats Bladebolt Outerbladewasher Withdoubledflats TowasherwithSpindle Lockbutton See Figures 13 Cutting a Slot in the Zero Clearance Throat PlateFraming Fence Squaring the Miter Table To the FenceMiter Head ScrewsSquaring the SAW Blade to Fence See Figures 17Combination Mm Socket HeadSquaring the Blade to Miter Table See FiguresDepth Stop Adjustments Bevellock Knob Positivestop Adjustment for 45ANGLESPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentUse only for the purposes listed below ApplicationsCutting with Your Compound Miter SAW To Crosscut with Your Miter SAWBevel CUT Leftsiderightside Leftht Indicatorindicator PointpointTo Bevel CUT with Your Miter SAW ClampCompound Miter CUT Bevelcut ClampCompound Mitercut Clamp To Make a Compound CUT with Your Miter SAWSupport Long Workpieces WorkpieceSee. Figures 29Longworkpiece Workpiecesupports Numberofsides COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Pitch of SideCeiling Cutting Crown MoldingLaying Molding Flat on Miter Table Clamping Wide Workpieces Cutting Warped MaterialWide Board Right Lubrication GeneralExtension Cords Brush Embly Brush CAP Assembly Dust BAG Brush ReplacementDustbag Exhaustport Table Extensions Extension Clamp Bracket Screw Holesfor Clamp Extensionrod Clamp AssemblyWork Clamp Clamp Extensionrod Bracket Small Screw Support WingscrewClampsupport Clampworkpieceto the Sawtable Clamping Workpiece to the FenceKnob Clamp Extensionrod Screws Clampworkpieceto the Fence FigCraftsman Compound Miter SAW- Model Number FigureADescription Quan KEY Part NO. NumberT633 Description Quan Parts List for Figure BFigureC STD315511 See Back page for Parts Ordering InstructionsPart Description Quan=800-366=7278 Days Week 11 p.m. CST

315.21222 specifications

The Craftsman 315.21222 is a versatile and powerful tool that stands out in the world of portable power equipment. Designed for both professionals and DIY enthusiasts, this product encapsulates precision, durability, and efficiency. It is most recognized as a portable air compressor, which is particularly favored for its functionality and robustness.

One of the main features of the Craftsman 315.21222 is its impressive air tank capacity, which ensures prolonged use without frequent refills. With a sizable tank, users can complete tasks that require sustained air pressure, making it ideal for various applications like inflating tires, powering pneumatic tools, and operating airbrushes. The quick recovery time of the compressor allows users to tackle jobs more efficiently, minimizing downtime.

Another noteworthy characteristic is its powerful motor, which delivers robust performance. It operates at a high PSI level, ensuring that it can handle demanding applications such as framing, roofing, and even spray painting. This feature makes the Craftsman 315.21222 an exceptional choice for professionals in the construction and automotive industries, as well as for home users embarking on renovation projects.

The technology employed in the Craftsman 315.21222 focuses on user comfort and safety. It comes equipped with an easy-to-read pressure gauge, allowing users to monitor the air pressure effectively. The compressor also features a thermal overload protector that prevents the motor from overheating during extended use, thereby enhancing the tool's longevity and reliability.

The design of the Craftsman 315.21222 is another factor contributing to its appeal. It features a compact and portable configuration, complete with sturdy wheels and a handle, making it easy to transport from one job site to another. This portability is essential for contractors who need to take their tools on the road or for hobbyists who require equipment that can be easily stored.

Lastly, the Craftsman brand is synonymous with quality and innovation, and the 315.21222 lives up to this reputation. The manufacturer provides excellent customer support and a warranty, which adds to the peace of mind for users. Whether for casual hobby use or serious professional tasks, the Craftsman 315.21222 is a reliable and efficient choice that meets a wide array of air compression needs.
Top Page Image Contents