Craftsman 315.21222 To Make a Compound CUT with Your Miter SAW, Compound Mitercut Clamp

Page 22

TO MAKE A COMPOUND CUT WITH YOUR MITER SAW:

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter lock

handle approximately one-half turn to the left to loosen.

•Press the miter lock plate down with your thumb and hold.

Rotate the control arm until the pointer aligns with the desired angle on the miter scale.

Release the miter lock plate.

Note: You can quickly locate 0°, 15°, 22-1/2 °, 31.62 °, and 45 ° left or right by releasing the miter lock plate as you rotate the control arm. The miter lock plate will seat itself in one of the positive stop notches, located in miter table frame.

•Tighten the miter lock handle securely.

WARNING: To avoid serious personal injury, always tighten the miter lock handle securely

before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

•Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

•Bevel angles can be set from 0°to 45 °.

•For your convenience there is a double scale located on the mounting bracket. See Figure 27. If one side becomes difficult to read as you move the saw arm to the left, simply refer to the other side. Align the indicator point for the side you choose with the desired angle.

•Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

•Recheck miter angle setting. Make a test cut in scrap material.

•Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. See Figures 33 and 34.

•When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table.

Align the cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C- clamp to secure the workpiece when possible. See Figure 29.

_IL WARNING: To avoid serious personal injury, always keep your hands outside the no hands

zone; at least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

COMPOUND

MITERCUT

C-CLAMP

Fig. 29

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 12 in. Compound Miter SAW Double Insulated Full ONE Year Warranty Double Insulation Symbolmeaning Safety Alert SymbolRemove Adjusting Keys Read ALL InstructionsInspect Extension Cords Periodi Make Sure the Miter Table and SAW Before Making a CUT, be Sure ALL Adjustments are SecureNever USE in AN Explosive Atmo Bevel Cut Rules For Safe OperationArea has Ample CrosscutKetscrew Miterlockhandle SawbladeDustguide FramingsquareAwarning / ADVERTENClA Cutting Capacities Bladeguard Sawarm Switch TriggerAMP Motor Know Your Compound Miter SAWCarrying Handle Switchtrigger Spindle Lockbutton Trigger LockPadlock Switch Carryinglockpin Handle SAW ARM MiterlockMounting Holes Electric BrakeFence Electrical ConnectionSee Figures 10, 11, Exhaust Port Dustguide To Install BladeLoosen Tighten Control Miter ARM Lockhandle Dust Guide Lower Bladeguard Phillips Screw Bolt LowerbladeDoubledflats Bladebolt Outerbladewasher Withdoubledflats TowasherwithSpindle Lockbutton Squaring the Miter Table To the Fence Cutting a Slot in the Zero Clearance Throat PlateFraming Fence See Figures 13See Figures 17 Head ScrewsSquaring the SAW Blade to Fence MiterSee Figures Mm Socket HeadSquaring the Blade to Miter Table CombinationBevel Pivot Adjustment Bevellock Knob Positivestop Adjustment for 45ANGLESPivot Adjustments Travel Pivot Adjustment Depth Stop AdjustmentsTo Crosscut with Your Miter SAW ApplicationsCutting with Your Compound Miter SAW Use only for the purposes listed belowClamp Leftsiderightside Leftht Indicatorindicator PointpointTo Bevel CUT with Your Miter SAW Bevel CUTBevelcut Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Compound Mitercut ClampSupport Long Workpieces WorkpieceSee. Figures 29Longworkpiece Workpiecesupports Pitch of Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters NumberofsidesCeiling Cutting Crown MoldingLaying Molding Flat on Miter Table Clamping Wide Workpieces Cutting Warped MaterialWide Board Right Lubrication GeneralExtension Cords Brush Embly Brush CAP Assembly Dust BAG Brush ReplacementDustbag Exhaustport Table Extensions Clamp Extensionrod Bracket Small Screw Support Wingscrew Clamp AssemblyWork Clamp Extension Clamp Bracket Screw Holesfor Clamp ExtensionrodClampworkpieceto the Fence Fig Clamping Workpiece to the FenceKnob Clamp Extensionrod Screws Clampsupport Clampworkpieceto the SawtableFigureA Craftsman Compound Miter SAW- Model NumberKEY Part NO. Number Description QuanT633 Parts List for Figure B Description QuanFigureC Description Quan See Back page for Parts Ordering InstructionsPart STD31551111 p.m. CST =800-366=7278 Days Week

315.21222 specifications

The Craftsman 315.21222 is a versatile and powerful tool that stands out in the world of portable power equipment. Designed for both professionals and DIY enthusiasts, this product encapsulates precision, durability, and efficiency. It is most recognized as a portable air compressor, which is particularly favored for its functionality and robustness.

One of the main features of the Craftsman 315.21222 is its impressive air tank capacity, which ensures prolonged use without frequent refills. With a sizable tank, users can complete tasks that require sustained air pressure, making it ideal for various applications like inflating tires, powering pneumatic tools, and operating airbrushes. The quick recovery time of the compressor allows users to tackle jobs more efficiently, minimizing downtime.

Another noteworthy characteristic is its powerful motor, which delivers robust performance. It operates at a high PSI level, ensuring that it can handle demanding applications such as framing, roofing, and even spray painting. This feature makes the Craftsman 315.21222 an exceptional choice for professionals in the construction and automotive industries, as well as for home users embarking on renovation projects.

The technology employed in the Craftsman 315.21222 focuses on user comfort and safety. It comes equipped with an easy-to-read pressure gauge, allowing users to monitor the air pressure effectively. The compressor also features a thermal overload protector that prevents the motor from overheating during extended use, thereby enhancing the tool's longevity and reliability.

The design of the Craftsman 315.21222 is another factor contributing to its appeal. It features a compact and portable configuration, complete with sturdy wheels and a handle, making it easy to transport from one job site to another. This portability is essential for contractors who need to take their tools on the road or for hobbyists who require equipment that can be easily stored.

Lastly, the Craftsman brand is synonymous with quality and innovation, and the 315.21222 lives up to this reputation. The manufacturer provides excellent customer support and a warranty, which adds to the peace of mind for users. Whether for casual hobby use or serious professional tasks, the Craftsman 315.21222 is a reliable and efficient choice that meets a wide array of air compression needs.
Top Page Image Contents