Craftsman 315.22811 owner manual Know Your Table SAW Bladeguard, Legstand, Frontrail Handle

Page 14

KNOW YOUR TABLE SAW

BLADEGUARD

SAW BLADE

RIVING KNIFE

MITER SCALE

SLIDING PAWLS_

MITERTABLE THROATPLATE

ADJUST

CLAMP

MITER

FENCE

QUICK-STOP

END CAP

MITER

FENCEHOLDER

STORAGE

BRACKETS)

LOCKINGCLAMPS

MITER

TABLE BASE

LEGSTAND

LEVELINGFOOl

REAR RAIL

RIP FENCE

ACCESSORY TABLE

FRONTRAIL

HANDLE

NITH

LOCKABLECOVER

BLADE

ADJUSTINGHANDLE

BEVEL

LOCKINGLEVER

BEVEL

INDICATOR

Figure 5

CRAFTSMAN"TABLESAW315,22811014

Image 14

Contents Product Rules OperatingInstructions before first use of this Full ONE Year Warranty on Craftsman Table SAW Rrftsmrn TABLESAW315.2281103CRAFTSMANTABLESAW315.228110 BladeCheckandBladeGuardAssembly21-33 Read ALL Instructions SymbolSafety Alert Symbol Do not USE in Dangerous EnvironNever USE this Tool in AN Explosive Save These INSTRUCTIONS. Refer to them Before Making a CUT, be sure all adjust- merits are secureUSE a Support for the Sides and Back Always Push the Workpiece never pull it toward the sawElectrical Connection Speed and WiringExtension Cords Grounding InstructionsSaw Blade Path ResinRip Cut SetDo not USE 7 in. Wobble Dadoes Wide Table KitFollowing items are included with your Table Saw RRAFTSMIIN TABLESAW315.228110 11CRRFTSMRNTABLESAW315.228110 Socketwrench WITH7/16in.SOCKETADJUSTABLE WrenchL,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i Combination SquareOperating Components Safety DevicesSpeed and Wiring 13CRRFTSMRNTABLESAW315.228110Miter Fenceholder Storage Brackets Lockingclamps Blade Adjustinghandle BevelKnow Your Table SAW Bladeguard LegstandTeeth Off position before plugging tool into the powerPadlock Notprovided SourceFiat washers 5/16 Hex nuts 5/16-18 Assembling LEG StandLeveling feet NUT LEVELINGFOOT--HEXLegstandassembled Figure Assembling Storage BracketsStoragebracketsupper Brace Lowerbrace Hexbolt Mounting the LEG Stand on the Table SAW BaseRAi To Install Miter Table and FenceEndcap Frontrail Scale HoldernutLock Lever To Install Accessory Table and RIP FenceHole B Tableslot Accessory Throatplate To Install Blade GuardSmallhex HexwrenchGroundingpin Coverofgrounded Outletbox GroundingTypes of Cuts Motor CordCuI-rlNG Tips CRRFTSI4RNTABLE SAW315.228110Innerandouterbladewasher Bevelblade Locking Lever Adjusting HandleThroatplatebladeguard To Remove the Blade Large Small HEX WrenchTocenterrivingknife Loosen Nuts Riving Knife Guard AssemblyRemove the Throat Plate Rearrangeshims FigureTo Avoid Kickback It is weUworth using precautions to avoid the risksTo Reduce Risk of Kickback Use these guidelines to avoid kickbackTo Make a Push Stick HOW to Make a FeatherboardHOW to Mount a Featherboard FeatherboardAdjustinghandle RIP Fence To Adjust the Blade DepthTo Adjust the Blade Angle AngledbladeMaking Cuts To Lock Miter TableMiter Slidelock To Make a Straight Cross CUTPushstick Blade Miterfence Guardassembly AdjustingclampTo Make a Straight RIP CUT BaseBevellockinglever Figure To Make a Bevel Cross CUTWoodeninsert RIP Fence Do not lock31CRRFTSMBNTABLESAW315,2281t0 Slidingmiteraccessory TableassemblytableTo Make a Large Panel CUT Raise the saw blade by pushing the bevel locking To Make NON-THROUGH CutsInarning Unplug the saw to avoid possible mlury Clamp Pushblock Bevellockinglever FigureAll blades must be rated For at least To Make Dado CutsUnplug your saw RPMBlade Adjusting Handle Bevelbevel General MaintenanceIndicator Lockinglever Screws Locknut BoltTo Check the Alignment of the RIP Fence to the Blade To Adjust the Bevel Locking LeverBlade Socketadjustingwheel TAB Hexnut CAM CompressionTo Align the Miter Locking Clamps To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table Replace the rails and check the rail cSamps37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 RRIIFTSMIIN TABLESAW315.228110 To Check Miter Fence AlignmentEight screws are visible on the miter base B Hex nuts on top of the miter table To Adjust the Miter FenceThere are four slides located under the sliding Eccentric Screw UP Ofbase SlideMiter Fence To Adjust QUICK-STOPMerindicator Miter Fence Zero DegreeBlade Adjusting Handle CRRFTSHRNTABLESAW315.22811042 Locker Bracket AssemblyThreaded Hole Bevel Gear Backupbracket Washer Tilt / Elevating Mechanism43rlIAFTSMAW TABLESAW315.228110 Not move smoothly Adjusted Adjust the rivingknife with shimsSliding miter table assembly does Blade is dullBlade makes poor cuts Blade adjusting handle is hard to turn Saw does not startSaw does not make accurate 90 or 45 degree cuts Motor labors in rip cut96,100 Forlegstandassembly Referto RgurefCraftsman 10 in. Table SAW Model no Screw 48 **STD60080373 **STD501003 75 *STDe01005 Key Part Number Description Quan 661811-001 410 Key Part Number Description QuanDescription Quan 49CRAFTSMANTABLESAW315.228110Key Part Number Description Quan CRAFTSMANTABLESAW315.22811050Standard Hardware Item --May Be Purchased Locally Key Part NumberKey Part Number 503Craftsman 10 in. Table SAW- Model no FigurefParts List for Figure F KEY Part Number Description QuanHomeCentralso