Craftsman owner manual 43rlIAFTSMAW TABLESAW315.228110

Page 43

43rlIAFTSMAW TABLESAW315.228110

Image 43

Contents Instructions before first use of this Rules OperatingProduct Rrftsmrn TABLESAW315.228110 Full ONE Year Warranty on Craftsman Table SAW21-33 BladeCheckandBladeGuardAssembly3CRAFTSMANTABLESAW315.228110 Do not USE in Dangerous Environ SymbolSafety Alert Symbol Read ALL InstructionsNever USE this Tool in AN Explosive Always Push the Workpiece never pull it toward the saw Before Making a CUT, be sure all adjust- merits are secureUSE a Support for the Sides and Back Save These INSTRUCTIONS. Refer to themGrounding Instructions Speed and WiringExtension Cords Electrical ConnectionSet ResinRip Cut Saw Blade PathWide Table Kit Do not USE 7 in. Wobble DadoesRRAFTSMIIN TABLESAW315.228110 Following items are included with your Table Saw11CRRFTSMRNTABLESAW315.228110 Combination Square WITH7/16in.SOCKETADJUSTABLE WrenchL,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i Socketwrench13CRRFTSMRNTABLESAW315.228110 Safety DevicesSpeed and Wiring Operating ComponentsLegstand Blade Adjustinghandle BevelKnow Your Table SAW Bladeguard Miter Fenceholder Storage Brackets LockingclampsSource Off position before plugging tool into the powerPadlock Notprovided TeethNUT LEVELINGFOOT--HEX Assembling LEG StandLeveling feet Fiat washers 5/16 Hex nuts 5/16-18Hexbolt Mounting the LEG Stand on the Table SAW Base Assembling Storage BracketsStoragebracketsupper Brace Lowerbrace Legstandassembled FigureHoldernut To Install Miter Table and FenceEndcap Frontrail Scale RAiHole B Tableslot Accessory To Install Accessory Table and RIP FenceLock Lever Hexwrench To Install Blade GuardSmallhex ThroatplateMotor Cord GroundingTypes of Cuts Groundingpin Coverofgrounded OutletboxCRRFTSI4RNTABLE SAW315.228110 CuI-rlNG TipsLarge Small HEX Wrench Bevelblade Locking Lever Adjusting HandleThroatplatebladeguard To Remove the Blade InnerandouterbladewasherRearrangeshims Figure Loosen Nuts Riving Knife Guard AssemblyRemove the Throat Plate TocenterrivingknifeUse these guidelines to avoid kickback It is weUworth using precautions to avoid the risksTo Reduce Risk of Kickback To Avoid KickbackFeatherboard HOW to Make a FeatherboardHOW to Mount a Featherboard To Make a Push StickAngledblade To Adjust the Blade DepthTo Adjust the Blade Angle Adjustinghandle RIP FenceTo Make a Straight Cross CUT To Lock Miter TableMiter Slidelock Making CutsBase Blade Miterfence Guardassembly AdjustingclampTo Make a Straight RIP CUT PushstickDo not lock To Make a Bevel Cross CUTWoodeninsert RIP Fence Bevellockinglever FigureTo Make a Large Panel CUT Slidingmiteraccessory Tableassemblytable31CRRFTSMBNTABLESAW315,2281t0 Clamp Pushblock Bevellockinglever Figure To Make NON-THROUGH CutsInarning Unplug the saw to avoid possible mlury Raise the saw blade by pushing the bevel lockingRPM To Make Dado CutsUnplug your saw All blades must be rated For at leastBolt General MaintenanceIndicator Lockinglever Screws Locknut Blade Adjusting Handle BevelbevelTAB Hexnut CAM Compression To Adjust the Bevel Locking LeverBlade Socketadjustingwheel To Check the Alignment of the RIP Fence to the BladeReplace the rails and check the rail cSamps To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Align the Miter Locking Clamps37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 Eight screws are visible on the miter base B To Check Miter Fence AlignmentRRIIFTSMIIN TABLESAW315.228110 Eccentric Screw UP Ofbase Slide To Adjust the Miter FenceThere are four slides located under the sliding Hex nuts on top of the miter tableDegree To Adjust QUICK-STOPMerindicator Miter Fence Zero Miter FenceTilt / Elevating Mechanism Locker Bracket AssemblyThreaded Hole Bevel Gear Backupbracket Washer Blade Adjusting Handle CRRFTSHRNTABLESAW315.2281104243rlIAFTSMAW TABLESAW315.228110 Blade is dull Adjust the rivingknife with shimsSliding miter table assembly does Not move smoothly AdjustedMotor labors in rip cut Blade adjusting handle is hard to turn Saw does not startSaw does not make accurate 90 or 45 degree cuts Blade makes poor cutsCraftsman 10 in. Table SAW Model no Forlegstandassembly Referto Rguref96,100 73 **STD501003 75 *STDe01005 48 **STD600803Screw Key Part Number Description Quan 49CRAFTSMANTABLESAW315.228110 410 Key Part Number Description QuanDescription Quan 661811-001CRAFTSMANTABLESAW315.22811050 Key Part Number Description Quan503 Key Part NumberKey Part Number Standard Hardware Item --May Be Purchased LocallyFiguref Craftsman 10 in. Table SAW- Model noKEY Part Number Description Quan Parts List for Figure FHomeCentralso