Craftsman 315.22811 Padlock Notprovided, Teeth, Off position before plugging tool into the power

Page 15

POWER SWITCH

See Figure 6.

Your saw is equipped with a switch that utilizes a Iockable switch cover to prevent unauthorized use. With the saw turned Off, a padlock can be used to secure the switch cover over the switch. This prevents anyone from starting your saw without removing the

padlock, lifting the switch cover, and pressing the switch button.

TO TURN YOUR SAW ON:

•Lift switch cover.

•Press switch button.

•Lower switch cover.

TO TURN YOUR SAW OFF:

•(A) Press or push outside of switch cover, or

(B)Lift switch cover and press switch button.

TO LOCK YOUR SAW SWITCH:

•Raise switch cover.

•Align metal loop through slot in switch cover while lowering switch cover.

•Place shackle of padlock (not provided) through the metal loop and close padlock.

SWITCH

TO

SWITCH

_TO START

I

(B)

TO LOCK IN

OFF POSITION

PADLOCK

(NOTPROVIDED)

Figure 6

CARBIDE

_1= W ARNING: Always make sure your workpiece =snot in contact with the blade before operating the switch to start the tool. Failure to heed this

warning may cause the workpiece to be kicked back toward the operator and result in serious personal injury.

TEETH

BLADE ROTATION

,_ WARNING: To reduce the risk of accidental starting, Always make sure the switch is in the

Off position before plugging tool into the power

source.

BLADES

See Figure 7.

For maximum performance, it is recommended that you use the Craftsman 40 tooth, 10 inch carbide

tipped combination blade provided with your saw. It is

a high-qualitycarbide tipped combination bladeFigure 7 suitable for ripping and crosscut operations. Other

recommended blades are listed in the accessory section of this manual.

Check with your nearest Sears Retail Store for other high quality blades as they become available.

_k CAUTION: Be sure to use only blades that are rated for at least 5,500 rpm and recommended for use on this saw. Check with your nearest Sears retail store.

15CRRFTSMRN"TABLESAW315.228110

Image 15

Contents Rules Operating Instructions before first use of thisProduct Rrftsmrn TABLESAW315.228110 Full ONE Year Warranty on Craftsman Table SAWBladeCheckandBladeGuardAssembly 21-333CRAFTSMANTABLESAW315.228110 Do not USE in Dangerous Environ SymbolSafety Alert Symbol Read ALL InstructionsNever USE this Tool in AN Explosive Always Push the Workpiece never pull it toward the saw Before Making a CUT, be sure all adjust- merits are secureUSE a Support for the Sides and Back Save These INSTRUCTIONS. Refer to themGrounding Instructions Speed and WiringExtension Cords Electrical ConnectionSet ResinRip Cut Saw Blade PathWide Table Kit Do not USE 7 in. Wobble DadoesRRAFTSMIIN TABLESAW315.228110 Following items are included with your Table Saw11CRRFTSMRNTABLESAW315.228110 Combination Square WITH7/16in.SOCKETADJUSTABLE WrenchL,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i Socketwrench13CRRFTSMRNTABLESAW315.228110 Safety DevicesSpeed and Wiring Operating ComponentsLegstand Blade Adjustinghandle BevelKnow Your Table SAW Bladeguard Miter Fenceholder Storage Brackets LockingclampsSource Off position before plugging tool into the powerPadlock Notprovided TeethNUT LEVELINGFOOT--HEX Assembling LEG StandLeveling feet Fiat washers 5/16 Hex nuts 5/16-18Hexbolt Mounting the LEG Stand on the Table SAW Base Assembling Storage BracketsStoragebracketsupper Brace Lowerbrace Legstandassembled FigureHoldernut To Install Miter Table and FenceEndcap Frontrail Scale RAiTo Install Accessory Table and RIP Fence Hole B Tableslot AccessoryLock Lever Hexwrench To Install Blade GuardSmallhex ThroatplateMotor Cord GroundingTypes of Cuts Groundingpin Coverofgrounded OutletboxCRRFTSI4RNTABLE SAW315.228110 CuI-rlNG TipsLarge Small HEX Wrench Bevelblade Locking Lever Adjusting HandleThroatplatebladeguard To Remove the Blade InnerandouterbladewasherRearrangeshims Figure Loosen Nuts Riving Knife Guard AssemblyRemove the Throat Plate TocenterrivingknifeUse these guidelines to avoid kickback It is weUworth using precautions to avoid the risksTo Reduce Risk of Kickback To Avoid KickbackFeatherboard HOW to Make a FeatherboardHOW to Mount a Featherboard To Make a Push StickAngledblade To Adjust the Blade DepthTo Adjust the Blade Angle Adjustinghandle RIP FenceTo Make a Straight Cross CUT To Lock Miter TableMiter Slidelock Making CutsBase Blade Miterfence Guardassembly AdjustingclampTo Make a Straight RIP CUT PushstickDo not lock To Make a Bevel Cross CUTWoodeninsert RIP Fence Bevellockinglever FigureSlidingmiteraccessory Tableassemblytable To Make a Large Panel CUT31CRRFTSMBNTABLESAW315,2281t0 Clamp Pushblock Bevellockinglever Figure To Make NON-THROUGH CutsInarning Unplug the saw to avoid possible mlury Raise the saw blade by pushing the bevel lockingRPM To Make Dado CutsUnplug your saw All blades must be rated For at leastBolt General MaintenanceIndicator Lockinglever Screws Locknut Blade Adjusting Handle BevelbevelTAB Hexnut CAM Compression To Adjust the Bevel Locking LeverBlade Socketadjustingwheel To Check the Alignment of the RIP Fence to the BladeReplace the rails and check the rail cSamps To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Align the Miter Locking Clamps37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 To Check Miter Fence Alignment Eight screws are visible on the miter base BRRIIFTSMIIN TABLESAW315.228110 Eccentric Screw UP Ofbase Slide To Adjust the Miter FenceThere are four slides located under the sliding Hex nuts on top of the miter tableDegree To Adjust QUICK-STOPMerindicator Miter Fence Zero Miter FenceTilt / Elevating Mechanism Locker Bracket AssemblyThreaded Hole Bevel Gear Backupbracket Washer Blade Adjusting Handle CRRFTSHRNTABLESAW315.2281104243rlIAFTSMAW TABLESAW315.228110 Blade is dull Adjust the rivingknife with shimsSliding miter table assembly does Not move smoothly AdjustedMotor labors in rip cut Blade adjusting handle is hard to turn Saw does not startSaw does not make accurate 90 or 45 degree cuts Blade makes poor cutsForlegstandassembly Referto Rguref Craftsman 10 in. Table SAW Model no96,100 48 **STD600803 73 **STD501003 75 *STDe01005Screw Key Part Number Description Quan 49CRAFTSMANTABLESAW315.228110 410 Key Part Number Description QuanDescription Quan 661811-001CRAFTSMANTABLESAW315.22811050 Key Part Number Description Quan503 Key Part NumberKey Part Number Standard Hardware Item --May Be Purchased LocallyFiguref Craftsman 10 in. Table SAW- Model noKEY Part Number Description Quan Parts List for Figure FHomeCentralso