Craftsman 315.22811 owner manual To Adjust QUICK-STOP, Merindicator Miter Fence Zero, Degree

Page 41

TO ADJUST QUICK-STOP

The quick-stop is preset at the factory to stop the miter fence at exactly zero degrees. However, when sliding miter table adjustments are made, these adjustments may cause the quick stop to need adjusting. Check quick-stop with miter scale set at

zero degrees. If adjustments are needed, proceed with the following steps:

•Loosen the eccentric screw holding the quick-stop.

•Place the quick-stop against the miter fence with miter scale set at zero degrees. See Figure 60.

•Adjust eccentric screw until it holds quick-stop securely against miter fence.

•Retighten hex nut, securing eccentric screw and quick-stop.

•Check your work. If the quick-stop is not at zero degrees, repeat steps 1-4.

M_ERINDICATOR

	MITER FENCE
ZERO	ADJUSTING CLAMP
DEGREE

MITER

FENCE

QUICK STOP AND
ECCENTRIC SCREW	Figure 60

41	CRAFTSMAN" TABLE SAW 315.228110

Image 41

Contents Product Rules OperatingInstructions before first use of this Rrftsmrn TABLESAW315.228110 Full ONE Year Warranty on Craftsman Table SAW3CRAFTSMANTABLESAW315.228110 BladeCheckandBladeGuardAssembly21-33 Safety Alert Symbol SymbolRead ALL Instructions Do not USE in Dangerous EnvironNever USE this Tool in AN Explosive USE a Support for the Sides and Back Before Making a CUT, be sure all adjust- merits are secureSave These INSTRUCTIONS. Refer to them Always Push the Workpiece never pull it toward the sawExtension Cords Speed and WiringElectrical Connection Grounding InstructionsRip Cut ResinSaw Blade Path SetWide Table Kit Do not USE 7 in. Wobble DadoesRRAFTSMIIN TABLESAW315.228110 Following items are included with your Table Saw11CRRFTSMRNTABLESAW315.228110 L,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i WITH7/16in.SOCKETADJUSTABLE WrenchSocketwrench Combination SquareSpeed and Wiring Safety DevicesOperating Components 13CRRFTSMRNTABLESAW315.228110Know Your Table SAW Bladeguard Blade Adjustinghandle BevelMiter Fenceholder Storage Brackets Lockingclamps LegstandPadlock Notprovided Off position before plugging tool into the powerTeeth SourceLeveling feet Assembling LEG StandFiat washers 5/16 Hex nuts 5/16-18 NUT LEVELINGFOOT--HEXStoragebracketsupper Brace Lowerbrace Assembling Storage BracketsLegstandassembled Figure Hexbolt Mounting the LEG Stand on the Table SAW BaseEndcap Frontrail Scale To Install Miter Table and FenceRAi HoldernutLock Lever To Install Accessory Table and RIP FenceHole B Tableslot Accessory Smallhex To Install Blade GuardThroatplate HexwrenchTypes of Cuts GroundingGroundingpin Coverofgrounded Outletbox Motor CordCRRFTSI4RNTABLE SAW315.228110 CuI-rlNG TipsThroatplatebladeguard To Remove the Blade Bevelblade Locking Lever Adjusting HandleInnerandouterbladewasher Large Small HEX WrenchRemove the Throat Plate Loosen Nuts Riving Knife Guard AssemblyTocenterrivingknife Rearrangeshims FigureTo Reduce Risk of Kickback It is weUworth using precautions to avoid the risksTo Avoid Kickback Use these guidelines to avoid kickbackHOW to Mount a Featherboard HOW to Make a FeatherboardTo Make a Push Stick FeatherboardTo Adjust the Blade Angle To Adjust the Blade DepthAdjustinghandle RIP Fence AngledbladeMiter Slidelock To Lock Miter TableMaking Cuts To Make a Straight Cross CUTTo Make a Straight RIP CUT Blade Miterfence Guardassembly AdjustingclampPushstick BaseWoodeninsert RIP Fence To Make a Bevel Cross CUTBevellockinglever Figure Do not lock31CRRFTSMBNTABLESAW315,2281t0 Slidingmiteraccessory TableassemblytableTo Make a Large Panel CUT Inarning Unplug the saw to avoid possible mlury To Make NON-THROUGH CutsRaise the saw blade by pushing the bevel locking Clamp Pushblock Bevellockinglever FigureUnplug your saw To Make Dado CutsAll blades must be rated For at least RPMIndicator Lockinglever Screws Locknut General MaintenanceBlade Adjusting Handle Bevelbevel BoltBlade Socketadjustingwheel To Adjust the Bevel Locking LeverTo Check the Alignment of the RIP Fence to the Blade TAB Hexnut CAM CompressionTo Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Align the Miter Locking Clamps Replace the rails and check the rail cSamps37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 RRIIFTSMIIN TABLESAW315.228110 To Check Miter Fence AlignmentEight screws are visible on the miter base B There are four slides located under the sliding To Adjust the Miter FenceHex nuts on top of the miter table Eccentric Screw UP Ofbase SlideMerindicator Miter Fence Zero To Adjust QUICK-STOPMiter Fence DegreeThreaded Hole Bevel Gear Backupbracket Washer Locker Bracket AssemblyBlade Adjusting Handle CRRFTSHRNTABLESAW315.22811042 Tilt / Elevating Mechanism43rlIAFTSMAW TABLESAW315.228110 Sliding miter table assembly does Adjust the rivingknife with shimsNot move smoothly Adjusted Blade is dullSaw does not make accurate 90 or 45 degree cuts Blade adjusting handle is hard to turn Saw does not startBlade makes poor cuts Motor labors in rip cut96,100 Forlegstandassembly Referto RgurefCraftsman 10 in. Table SAW Model no Screw 48 **STD60080373 **STD501003 75 *STDe01005 Key Part Number Description Quan Description Quan 410 Key Part Number Description Quan661811-001 49CRAFTSMANTABLESAW315.228110CRAFTSMANTABLESAW315.22811050 Key Part Number Description QuanKey Part Number Key Part NumberStandard Hardware Item --May Be Purchased Locally 503Figuref Craftsman 10 in. Table SAW- Model noKEY Part Number Description Quan Parts List for Figure FHomeCentralso

TO ADJUST QUICK-STOP

M_ERINDICATOR

MITER FENCE

ZERO

DEGREE

MITER

FENCE

QUICK STOP AND

ECCENTRIC SCREW