Stow MS2090HP, MS2050E3 Stowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine, Engine Troubleshooting

Page 36

STOWTRAK 20 SAW —TROUBLESHOOTING (GASOLINE ENGINE)

Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 8) information shown below and on the following page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business office or service plant.

TABLE 8. ENGINE TROUBLESHOOTING

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

 

 

 

Difficult to start

 

 

 

 

 

 

Ignition plug being bridged (shorted)?

Check ignition system.

 

 

 

Fuel is available but spark plug

Carbon deposit at ignition?

Clean or replace ignition.

 

 

will not ignite. (Power available

 

Replace insulators.

at high tension cable).

Short circuit due to defective insulators?

 

 

 

 

 

Improper spark gap?

Set spark plug gap to the correct gap.

 

 

 

Fuel is available but spark plug

Short circuit at stop switch?

Check stop switch circuit. Replace stop switch if defective.

will not ignite. (Power NOT

 

 

 

 

available at high tension cable).

Ignition coil defective?

Replace ignition coil.

 

 

 

 

Defective cylinder head gasket?

Tighten cylinder head bolts or replace head gasket.

Fuel is available and spark plug

 

 

Cylinder worn?

Replace cylinder.

ignites (compressionlow ).

 

 

 

Spark plug loose?

Tighen spark plug.

 

 

 

Operation not satisfactory

 

 

 

 

 

 

Air cleaner clogged?

Clean or replace air cleaner.

 

 

 

Not enough power available

Fuel level in carbureator float chamber

Adjust carbureator float

improper?

(compression normal, no miss-

 

 

 

firing).

Muffler clogged with carbon deposits?

Clean or replace muffler.

 

 

 

 

 

Fuel in use inadequate (water, dust)?

Flush fuel sytem and replace with fresh fuel.

 

 

 

 

Ignition coil defective?

Flush fuel sytem and replace with fresh fuel.

 

 

 

 

Air in fuel line?

Bleed (remove air) from fuel line.

Not enough power available

 

 

 

 

(compression normal, miss-

Carbon deposits in cylinder?

Clean or replace cylinder

firing).

 

 

Ignition plug often shorts?

Replace ignition wires, clean ignition.

 

 

 

 

 

Fuel in use inadequate (water, dust)?

Flush fuel sytem and replace with fresh fuel.

 

 

 

 

Excessive carbon depostion in

Clean or replace crankcase.

 

combustion chamber?

 

Engine overheats.

 

 

Exhaust or muffler clogged with carbon.

Clean or replace muffler.

 

 

 

 

 

Spark plug heat value incorrect?

Replace spark plug with correct type spark plug.

 

 

 

PAGE 36 — STOW TRAK-20 SAW — OPERATIONS MANUAL — REV. #1 (06/16/04)

Image 36
Contents Models MS2050E1, MS2050E3, MS2090HP 2 Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Post Office Box Stow Carson, Ca Email stow@multiquip.comStow TRAK-20 Masonry SAW Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 SAW Specifications Electric MOTOR/GAS Engine SpecificationsStowtrak 20 SAW Dimensions DimensionsStowtrak 20 SAW Safety Message Alert Symbols Hazard SymbolsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearStowtrak 20 SAW Safety Message Alert Symbols This saw, other property, orSafety Safety Gasoline Powered EnginesStowtrak 20 SAW Rules for Safe Operation Safety Electric Powered Models General SafetyBlade Safety Stowtrak 20 SAW Rules for Safe OperationSaw Maintenance Cleaning SawTransportation SafetyEmergencies Stowtrak 20 SAW Operation and Safety Decals Machine Operation And Safety DecalsStowtrak 20 SAW General Information Trak 20 Masonry SawStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Stowtrak 20 SAW Controls and Components Trak 20 Saw Electric ModelsStopper Place stopper in tray when filling with water Stowtrak 20 SAW Controls and ComponentsStowtrak 20 SAW Electric Motor Components Heavy Duty Electric MotorsStowtrak 20 SAW Gasoline Engine Components Honda GX270QWH2 Gasoline EngineOperating the engine without an Muffler Used to reduce noise and emissionsStowtrak 20 SAW PRE-SETUP Electric Motors Pre-SetupAssembly Electric Powered Saws Only Conveyor Cart PlacementStowtrak 20 SAW PRE-SETUP Electric Motors Blade InstallationSaw Blades Saw Blade Definitions FigureConnecting the Power Figure Place the power ON/OFF switch in the OFF position downDry Cutting Electric Saws Only Stowtrak 20 SAW PRE-SETUP Gasoline Engine Assembly Gasoline Powered Saws OnlyWet Cutting Setup Gasoline Only Mechanical water pump isStowtrak 20 SAW PRE-SETUP Gasoline Engine OIL TypeShutdown Procedure Stowtrak 20 SAW STARTUP/SHUTDOWN Electric MotorsStart-up Electric Motor Stowtrak 20 SAW STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripOperation Fixed Height Cutting MethodStep Pedal Cutting Method Jamming the blade intoStow Trak 20 SAW Maintenance SAW Stow Trak 20 SAW Maintenance SAW Adjust Belt Tension Gasoline Powered SawsTo adjust engine-to-jackshaft belts only To adjust jackshaft-to-bladeshaft beltCutting Head Alignment Blade Horizontal Cutting Head AlignmentTighten the set screws CheckingVertical Cutting Head AlignmentStowtrak 20 SAW Maintenance Gasoline Engine Engine MaintenanceStowtrak 20 SAW Maintenance Gasoline Engine Engine Air CleanerDaily WeeklyStowtrak 20 SAW Enginewiring Diagram Stowtrak 20 SAW -TROUBLESHOOTING Blade Blade TroubleshootingStowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine Engine TroubleshootingStowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine Stowtrak 20 SAW -TROUBLESHOOTING Electric Motor Troubleshooting Electric MotorStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Your Local Dealer is