Stow MS2090HP, MS2050E3, MS2050E1 manual Stopping the Engine, Starter Grip

Page 27

STOWTRAK 20 SAW — STARTUP/SHUTDOWN (GASOLINE ENGINE)

5.Grasp the starter grip (Figure 23) and slowly pull it out. The resistance becomes the hardest at a certain posi- tion, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting.

Figure 23. Starter Grip

CAUTION - Engine Starter Rope Safety

DO NOT pull the starter rope all the way to the end. DO NOT release the starter rope after pulling. Allow it to rewind as soon as possible. Failure to do so could damage your engine.

6.If the engine has started, slowly return the choke lever (Figure 21) to the OPEN position. If the engine has not started repeat steps 1 through 5.

7.Before the saw is placed into operation, run the engine for several minutes. Check for fuel leaks, and noises that would associate with loose guards and/or covers.

8.Gradually move the engine throttle lever toward the fast position. (All cutting should be done at full throttle).

9.Avoid overloading the engine when cutting. In the event that the engine becomes overloaded, turn the engine ON/OFF switch to the OFF position (Figure 25) and allow the engine to cool before attempting to restart.

WARNING - Burn Hazard

Engine components can generate extreme heat.To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

Stopping the Engine

1. Set the engine throttle lever to slow speed and let the engine idle for 3-5 minutes.

2.Turn the engine ON/OFF switch to the OFF position (Figure 25).

3.Place the fuel valve lever in the closed position.

4.Let the engine cool.

5.Using a soft cloth, clean any excess debris or residue that may have accumulated on the saw.

6.Store saw in a clean dry location where it will be out of the reach of children.

WARNING - Engine Speed when Cutting

ALWAYS cut with the saw at FULL THROTTLE. Attempting to cut with the saw at less than full throttle could cause the blade to bind or stop abruptly in the slab resulting in serious injury to the operator or others in the area.

STOW TRAK-20 SAW — OPERATIONS MANUAL — REV. #1 (06/16/04) — PAGE 27

Image 27
Contents Models MS2050E1, MS2050E3, MS2090HP 2 Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Email stow@multiquip.com Post Office Box Stow Carson, CaStow TRAK-20 Masonry SAW Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Electric MOTOR/GAS Engine Specifications SAW SpecificationsDimensions Stowtrak 20 SAW DimensionsRotating blade can cut and crush Keep hands and feet clear Stowtrak 20 SAW Safety Message Alert SymbolsHazard Symbols Safety Message Alert SymbolsThis saw, other property, or Stowtrak 20 SAW Safety Message Alert SymbolsSafety Safety Gasoline Powered EnginesStowtrak 20 SAW Rules for Safe Operation Stowtrak 20 SAW Rules for Safe Operation Safety Electric Powered ModelsGeneral Safety Blade SafetySaw Maintenance Cleaning SawTransportation SafetyEmergencies Machine Operation And Safety Decals Stowtrak 20 SAW Operation and Safety DecalsTrak 20 Masonry Saw Stowtrak 20 SAW General InformationStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Trak 20 Saw Electric Models Stowtrak 20 SAW Controls and ComponentsStowtrak 20 SAW Controls and Components Stopper Place stopper in tray when filling with waterHeavy Duty Electric Motors Stowtrak 20 SAW Electric Motor ComponentsMuffler Used to reduce noise and emissions Stowtrak 20 SAW Gasoline Engine ComponentsHonda GX270QWH2 Gasoline Engine Operating the engine without anConveyor Cart Placement Stowtrak 20 SAW PRE-SETUP Electric MotorsPre-Setup Assembly Electric Powered Saws OnlySaw Blade Definitions Figure Stowtrak 20 SAW PRE-SETUP Electric MotorsBlade Installation Saw BladesConnecting the Power Figure Place the power ON/OFF switch in the OFF position downDry Cutting Electric Saws Only Mechanical water pump is Stowtrak 20 SAW PRE-SETUP Gasoline EngineAssembly Gasoline Powered Saws Only Wet Cutting Setup Gasoline OnlyOIL Type Stowtrak 20 SAW PRE-SETUP Gasoline EngineShutdown Procedure Stowtrak 20 SAW STARTUP/SHUTDOWN Electric MotorsStart-up Electric Motor Place the Choke Lever in the Closed position Stowtrak 20 SAW STARTUP/SHUTDOWN Gasoline EngineStarter Grip Stopping the EngineJamming the blade into OperationFixed Height Cutting Method Step Pedal Cutting MethodStow Trak 20 SAW Maintenance SAW To adjust jackshaft-to-bladeshaft belt Stow Trak 20 SAW Maintenance SAWAdjust Belt Tension Gasoline Powered Saws To adjust engine-to-jackshaft belts onlyCheckingVertical Cutting Head Alignment Cutting Head Alignment BladeHorizontal Cutting Head Alignment Tighten the set screwsEngine Maintenance Stowtrak 20 SAW Maintenance Gasoline EngineWeekly Stowtrak 20 SAW Maintenance Gasoline EngineEngine Air Cleaner DailyStowtrak 20 SAW Enginewiring Diagram Blade Troubleshooting Stowtrak 20 SAW -TROUBLESHOOTING BladeEngine Troubleshooting Stowtrak 20 SAW -TROUBLESHOOTING Gasoline EngineStowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine Troubleshooting Electric Motor Stowtrak 20 SAW -TROUBLESHOOTING Electric MotorStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Your Local Dealer is