Stow MS2050E1, MS2090HP, MS2050E3 Stowtrak 20 SAW Safety Message Alert Symbols, Hazard Symbols

Page 8

STOWTRAK 20 SAW — SAFETY MESSAGE ALERT SYMBOLS

FORYOUR SAFETY AND THE SAFETY OF OTHERS!

HAZARD SYMBOLS

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Owner's Manual has been developed to provide

NOTEcomplete instructions for the safe and efficient operation of the STOWTRAK-20.

For engine maintenance information, please refer to the engine manufacturers instructions for data relative to its safe operation.

Before using this MASONRY SAW, ensure that the operating individual has read and understands all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER

You WILL be KILLED or SERIOUSLY injured if you DO NOT follow directions.

WARNING

You CAN be KILLED or SERIOUSLY injured if you DO NOT follow directions.

CAUTION

You CAN be injured if you DO NOT follow directions.

Potential hazards associated with operation of the pump will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols. Some examples are listed below:

WARNING - Guards and Covers In Place

NEVER operate the saw without blade guards and covers in place. Adhere to safety guidelines ANSI American National Standards Institute, OSHA or other applicable local regulations.

WARNING - Rotating Blade

Rotating blade can cut and crush.

Keep hands and feet clear.

WARNING - Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

WARNING - Rotating Parts

NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

PAGE 8 — STOW TRAK-20 SAW — OPERATIONS MANUAL — REV. #1 (06/16/04)

Image 8
Contents Models MS2050E1, MS2050E3, MS2090HP 2 Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Post Office Box Stow Carson, Ca Email stow@multiquip.comStow TRAK-20 Masonry SAW Stow TRAK-20 SAW Operations Manual REV. #1 06/16/04 SAW Specifications Electric MOTOR/GAS Engine SpecificationsStowtrak 20 SAW Dimensions DimensionsStowtrak 20 SAW Safety Message Alert Symbols Hazard SymbolsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearStowtrak 20 SAW Safety Message Alert Symbols This saw, other property, orStowtrak 20 SAW Rules for Safe Operation SafetySafety Gasoline Powered Engines Safety Electric Powered Models General SafetyBlade Safety Stowtrak 20 SAW Rules for Safe OperationEmergencies Saw Maintenance CleaningSawTransportation Safety Stowtrak 20 SAW Operation and Safety Decals Machine Operation And Safety DecalsStowtrak 20 SAW General Information Trak 20 Masonry SawStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Stowtrak 20 SAW Controls and Components Trak 20 Saw Electric ModelsStopper Place stopper in tray when filling with water Stowtrak 20 SAW Controls and ComponentsStowtrak 20 SAW Electric Motor Components Heavy Duty Electric MotorsStowtrak 20 SAW Gasoline Engine Components Honda GX270QWH2 Gasoline EngineOperating the engine without an Muffler Used to reduce noise and emissionsStowtrak 20 SAW PRE-SETUP Electric Motors Pre-SetupAssembly Electric Powered Saws Only Conveyor Cart PlacementStowtrak 20 SAW PRE-SETUP Electric Motors Blade InstallationSaw Blades Saw Blade Definitions FigureDry Cutting Electric Saws Only Connecting the Power FigurePlace the power ON/OFF switch in the OFF position down Stowtrak 20 SAW PRE-SETUP Gasoline Engine Assembly Gasoline Powered Saws OnlyWet Cutting Setup Gasoline Only Mechanical water pump isStowtrak 20 SAW PRE-SETUP Gasoline Engine OIL TypeStart-up Electric Motor Shutdown ProcedureStowtrak 20 SAW STARTUP/SHUTDOWN Electric Motors Stowtrak 20 SAW STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripOperation Fixed Height Cutting MethodStep Pedal Cutting Method Jamming the blade intoStow Trak 20 SAW Maintenance SAW Stow Trak 20 SAW Maintenance SAW Adjust Belt Tension Gasoline Powered SawsTo adjust engine-to-jackshaft belts only To adjust jackshaft-to-bladeshaft beltCutting Head Alignment Blade Horizontal Cutting Head AlignmentTighten the set screws CheckingVertical Cutting Head AlignmentStowtrak 20 SAW Maintenance Gasoline Engine Engine MaintenanceStowtrak 20 SAW Maintenance Gasoline Engine Engine Air CleanerDaily WeeklyStowtrak 20 SAW Enginewiring Diagram Stowtrak 20 SAW -TROUBLESHOOTING Blade Blade TroubleshootingStowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine Engine TroubleshootingStowtrak 20 SAW -TROUBLESHOOTING Gasoline Engine Stowtrak 20 SAW -TROUBLESHOOTING Electric Motor Troubleshooting Electric MotorStow TRAK-20 SAW Operations Manual REV. #1 06/16/04 Your Local Dealer is