Stow CD6CE13H18 Stow Cutter 1 CE SAW- Blade Placement, Blade Removal and Replacement

Page 19

STOW CUTTER 1 CE SAW— BLADE PLACEMENT

6.Inner Flange (Collar) - This flange is fixed upon the spindle. The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade.

Blade Removal and Replacement

1.Set the ENGINE ON/OFF switches to the "OFF" position to prevent accidental starting.

2.Place the saw on a stable level working surface.

3.Ensure the blade is raised and the raise/lower crank is locked into position.

When removing or installing a

NOTE diamond blade, please note that the blade retaining nuts are left and right- hand threaded.

4. Lift up the blade guard cover to gain access to the blade.

Figure 11.Tool (Blade) Placement

WARNING

Incorrectly installed blades can cause damage to the blade or equipment or cause injury due to breakage.

WARNING

Dropping or forcing the blade onto the cutting surface can severely damage the diamond blade and may cause serious damage to the saw and bodily harm.

Figure 12. Tool (Blade) Wrench

5.Use the provided blade nut wrench to remove and install the blade. (Figure 12)

6.Unscrew the spindle nut (right side loosens clockwise and tightens counter-clockwise while the left side loosens counter-clockwise and tightens clockwise). DO NOT overtighten the nut (approximately 45-50 ft. lb/61-68 N/m) when finalizing the assembly.

STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 19

Image 19
Contents Model CD6CE13H18 Stow Cutter 1 CE SAW Proposition 65 Warning Silicosis Warning Stow Cutter 1 CE SAW SILICOSIS/RESPIRATORYWARNINGSStow Cutter 1 CE SAW Table of Contents If you do not follow these directions Stow Cutter 1 CE SAW Safety Message Alert SymbolsAlways wear approved respiratory protection Always wear approved eye and hearing protectionRules for Safe Operation SafetyNever use fuel as a cleaning agent Stow Cutter 1 CE SAW Rules for Safe OperationDiamond Blade Safety General SafetyApply the brakes when leaving or when using on a slope Machine Operation And Safety Decals Saw Transportation SafetyEmergencies Description Stow Cutter 1 CE SAW Specifications SAWDimension cm SideViewGX390K1QWT2/GX390U1QWT2 Stow Cutter 1 CE SAW Specifications EngineStow Cutter 1 CE SAW General Information Handle Lock Lock blade depth to desired position BeltTension Adjuster Adjusts belt tensionStow Cutter 1 CE SAW Controls & Components Controls & ComponentsSpark plug once a month Starting, OFF position stops engine operationsSmoothly Flow of fuelFuel Check Stow Cutter 1 CE SAW PREPARATION/PRE-INSPECTIONPreparation / PRE-INSPECTION Engine Oil CheckBelt Alignment and Tensioning Adjusting belt tensionGuards And Covers Belt CheckSpecifictoolsto be Used Stow Cutter 1 CE SAW- BladesRefer to Figure Blade PlacementDiamond Blades Blade SpeedBlade Removal and Replacement Stow Cutter 1 CE SAW- Blade PlacementStow Cutter 1 CE SAW- RAISE/LOWER and Depth Stop Setting the Depth StopRaise/Lower and Depth Stop Initial START-UP Stow Cutter 1 CE SAW Initial START-UPPlace the fuel valve lever to the on position Place the Choke Lever in the Closed position Stow Cutter 1 CE SAW Initial START-UPOperation Stow Cutter 1 CE SAW OperationCutting Close to aVertical Surface Restarting After InterventionMaintenance Stow Cutter 1 CE SAW MaintenanceFuel line Front Pointer AdjustmentEngine oil change Engine tank & strainerReplacethehardplastictubebackintothe WaterTankvalve Locate all parts listed in the parts listStow Cutter 1 CE SAW Optional Watertank Watertank KIT OptionDecommissioning Saw/Components Stow Cutter 1 CE SAW Optional WatertankStow Cutter 1 CE SAW Troubleshooting SAW Replace piston rings and/or Clean or replace spark plugCheck switch wiring, replace Replace defective spark plugWith correct type of fuel Stow Cutter 1 CE SAW Troubleshooting EngineSymptom Possible Cause Solution With correct type fuelEffective July 15 Special order items are not returnable for creditPage Your Local Dealer is HERE’S HOW to GET Help