Stow CD6CE13H18 operation manual Clean or replace spark plug, Check switch wiring, replace

Page 30

STOW CUTTER 1 CE SAW — TROUBLESHOOTING (ENGINE)

TABLE 6. TROUBLESHOOTING (ENGINE)

SYMPTOM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

Spark plug bridging?

Check gap, insulation or

 

replace spark plug.

 

 

 

 

 

 

Carbon deposit on spark plug?

Clean or replace spark plug.

Difficult to start, "fuel is available, but no

 

 

Short circuit due to deficient spark plug

Check spark plug insulation,

SPARK at spark plug".

insulation?

replace if worn.

 

 

 

 

 

Improper spark plug gap?

Set to proper gap.

 

 

 

 

Ignition coil defective?

Replace ignition coil.

 

 

 

 

ON/OFF switch is shorted?

Check switch wiring, replace

 

switch.

 

 

 

 

 

 

Improper spark gap, points dirty?

Set correct spark gap and

Difficult to start, "fuel is available, and

clean points.

 

 

 

SPARK is present at the spark plug".

Condenser insulation worn or short

Replace condenser.

 

 

circuiting?

 

 

 

 

 

 

Spark plug wire broken or short circuiting?

Replace defective spark plug

 

wiring.

 

 

 

 

 

 

Wrong fuel type?

Flush fuel system, and replace

 

with correct type of fuel.

 

 

 

 

 

Difficult to start, "fuel is available, spark

Water or dust in fuel system?

Flush fuel system.

is present and compression is normal".

 

 

Air cleaner dirty?

Replace air cleaner.

 

 

 

 

 

Choke Open?

Close Choke.

 

 

 

 

Suction/exhaust valve stuck or protruded?

Re-seat valves.

 

 

 

 

Piston ring and/or cylinder worn?

Replace piston rings and/or

 

piston.

Difficult to start, "fuel is available, spark

 

 

 

 

 

is present and compression is low".

Cylinder head and/or spark plug not

Torque cylinder head bolts and

 

tightened properly?

spark plug.

 

 

 

 

Head gasket and/or spark plug gasket

Replace head and/or spark plug

 

damaged?

gaskets.

 

 

 

 

Fuel not available in fuel tank (tank empy)?

Fill with correct type of fuel.

 

 

 

 

Fuel filter clogged?

Replace fuel filter.

No fuel present at the carburetor.

 

 

Fuel tank cap breather hole clogged?

Clean or replace fuel tank cap.

 

 

 

 

 

Air in fuel line?

Bleed fuel line.

 

 

 

PAGE 30 — STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07)

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Model CD6CE13H18 Stow Cutter 1 CE SAW Proposition 65 Warning Stow Cutter 1 CE SAW SILICOSIS/RESPIRATORYWARNINGS Silicosis WarningStow Cutter 1 CE SAW Table of Contents Stow Cutter 1 CE SAW Safety Message Alert Symbols If you do not follow these directionsAlways wear approved eye and hearing protection Always wear approved respiratory protectionStow Cutter 1 CE SAW Rules for Safe Operation SafetyNever use fuel as a cleaning agent Rules for Safe OperationGeneral Safety Diamond Blade SafetyApply the brakes when leaving or when using on a slope Saw Transportation Safety Machine Operation And Safety DecalsEmergencies SideView Stow Cutter 1 CE SAW Specifications SAWDimension cm DescriptionStow Cutter 1 CE SAW Specifications Engine GX390K1QWT2/GX390U1QWT2Stow Cutter 1 CE SAW General Information Controls & Components BeltTension Adjuster Adjusts belt tensionStow Cutter 1 CE SAW Controls & Components Handle Lock Lock blade depth to desired positionFlow of fuel Starting, OFF position stops engine operationsSmoothly Spark plug once a monthEngine Oil Check Stow Cutter 1 CE SAW PREPARATION/PRE-INSPECTIONPreparation / PRE-INSPECTION Fuel CheckBelt Check Adjusting belt tensionGuards And Covers Belt Alignment and TensioningStow Cutter 1 CE SAW- Blades Specifictoolsto be UsedBlade Speed Blade PlacementDiamond Blades Refer to FigureStow Cutter 1 CE SAW- Blade Placement Blade Removal and ReplacementSetting the Depth Stop Stow Cutter 1 CE SAW- RAISE/LOWER and Depth StopRaise/Lower and Depth Stop Stow Cutter 1 CE SAW Initial START-UP Initial START-UPPlace the fuel valve lever to the on position Stow Cutter 1 CE SAW Initial START-UP Place the Choke Lever in the Closed positionStow Cutter 1 CE SAW Operation OperationRestarting After Intervention Cutting Close to aVertical SurfaceStow Cutter 1 CE SAW Maintenance MaintenanceEngine tank & strainer Front Pointer AdjustmentEngine oil change Fuel lineWatertank KIT Option Locate all parts listed in the parts listStow Cutter 1 CE SAW Optional Watertank Replacethehardplastictubebackintothe WaterTankvalveStow Cutter 1 CE SAW Optional Watertank Decommissioning Saw/ComponentsStow Cutter 1 CE SAW Troubleshooting SAW Replace defective spark plug Clean or replace spark plugCheck switch wiring, replace Replace piston rings and/orWith correct type fuel Stow Cutter 1 CE SAW Troubleshooting EngineSymptom Possible Cause Solution With correct type of fuelSpecial order items are not returnable for credit Effective July 15Page HERE’S HOW to GET Help Your Local Dealer is
Top Page Image Contents