Stow CD6CE13H18 operation manual Stow Cutter 1 CE SAW Safety Message Alert Symbols

Page 5

STOW CUTTER 1 CE SAW — SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and comply with the Safety Messages and Operating Instructions could result in injury to yourself or others.

NOTE

This Owner's Manual has been developed to provide instructions for the safe and efficient operation of the STOW CUTTER 1 CE SAW. For engine maintenance information, please refer to the engine manufacturers' instructions for data relative to its safe operation.

Before using this CONCRETE/ASPHALT SAW, ensure that the operating individual has read and understands all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER

You WILL be KILLED or SERIOUSLY INJURED

if you DO NOT follow these directions.

HAZARD SYMBOLS

Lethal Exhaust Gases

Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.

Guards and Covers In Place

NEVER operate the saw without blade guards and covers in place. Adhere to safety guidelines and applicable local regulations.

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if

you DO NOT follow these directions.

CAUTION

You CAN be INJURED if you DO NOT follow these directions.

Potential hazards associated with CUTTER 1 CE operation will be referenced with "Hazard Symbols" which appear throughout this manual, and will be referenced in conjunction with Safety "Message Alert Symbols".

Rotating Parts

NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 5

Image 5
Contents Model CD6CE13H18 Stow Cutter 1 CE SAW Proposition 65 Warning Silicosis Warning Stow Cutter 1 CE SAW SILICOSIS/RESPIRATORYWARNINGSStow Cutter 1 CE SAW Table of Contents If you do not follow these directions Stow Cutter 1 CE SAW Safety Message Alert SymbolsAlways wear approved respiratory protection Always wear approved eye and hearing protectionNever use fuel as a cleaning agent SafetyStow Cutter 1 CE SAW Rules for Safe Operation Rules for Safe OperationApply the brakes when leaving or when using on a slope General SafetyDiamond Blade Safety Emergencies Saw Transportation SafetyMachine Operation And Safety Decals Dimension cm Stow Cutter 1 CE SAW Specifications SAWSideView DescriptionGX390K1QWT2/GX390U1QWT2 Stow Cutter 1 CE SAW Specifications EngineStow Cutter 1 CE SAW General Information Stow Cutter 1 CE SAW Controls & Components BeltTension Adjuster Adjusts belt tensionControls & Components Handle Lock Lock blade depth to desired positionSmoothly Starting, OFF position stops engine operationsFlow of fuel Spark plug once a monthPreparation / PRE-INSPECTION Stow Cutter 1 CE SAW PREPARATION/PRE-INSPECTIONEngine Oil Check Fuel CheckGuards And Covers Adjusting belt tensionBelt Check Belt Alignment and TensioningSpecifictoolsto be Used Stow Cutter 1 CE SAW- BladesDiamond Blades Blade PlacementBlade Speed Refer to FigureBlade Removal and Replacement Stow Cutter 1 CE SAW- Blade PlacementRaise/Lower and Depth Stop Setting the Depth StopStow Cutter 1 CE SAW- RAISE/LOWER and Depth Stop Place the fuel valve lever to the on position Stow Cutter 1 CE SAW Initial START-UPInitial START-UP Place the Choke Lever in the Closed position Stow Cutter 1 CE SAW Initial START-UPOperation Stow Cutter 1 CE SAW OperationCutting Close to aVertical Surface Restarting After InterventionMaintenance Stow Cutter 1 CE SAW MaintenanceEngine oil change Front Pointer AdjustmentEngine tank & strainer Fuel lineStow Cutter 1 CE SAW Optional Watertank Locate all parts listed in the parts listWatertank KIT Option Replacethehardplastictubebackintothe WaterTankvalveDecommissioning Saw/Components Stow Cutter 1 CE SAW Optional WatertankStow Cutter 1 CE SAW Troubleshooting SAW Check switch wiring, replace Clean or replace spark plugReplace defective spark plug Replace piston rings and/orSymptom Possible Cause Solution Stow Cutter 1 CE SAW Troubleshooting EngineWith correct type fuel With correct type of fuelEffective July 15 Special order items are not returnable for creditPage Your Local Dealer is HERE’S HOW to GET Help