Functional Description, Assembly, Operation

IMPORTANT SAFETY

INSTRUCTIONSENC007-4

FOR BATTERY CARTRIDGE

1.Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2.Do not disassemble battery cartridge.

3.If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4.If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5.Do not short the battery cartridge:

(1)Do not touch the terminals with any conductive material.

(2)Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.

(3)Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6.Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).

7.Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

8.Be careful not to drop or strike battery.

9.Do not use dropped or struck battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1.Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2.Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3.Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge (Fig. 1)

•Open Sprayer’s battery pack cover.

•Always switch off the tool before insertion or removal of the battery cartridge.

•To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.

•To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

•Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Spray pipe and nozzle assembly method (Fig. 2)

•As shown in the diagram, assemble spray pipe and then nozzle onto lever cock.

•Adjust direction of nozzle using nut on spray pipe.

•Firmly attach components to ensure there is no leaking.

•Select nozzle according to type of spraying to be done.

NOTE:

•All connector units use packing. Before assembly, always check to see that the units have packing.

•Check to make sure that the spray hose is not cracked, worn and/or damaged.

•Firmly tighten on the spray pipe to prevent liquid leaks.

•If there is a leak from a connector unit, tighten further using a hand tool (by approximately 45 degrees).

•Do not use a spray pipe that is longer than the standard one provided. Doing so may cause leaking from connector units.

Back strap attaching method (Fig. 3)

Use the diagram pointers to attach the back strap at top and bottom, making sure there are no twists in the strap.

NOTE:

•Check to make sure that back strap is securely attached to chemical tank.

OPERATION

CAUTION:

•Before inserting the battery cartridge into the tool, always check to see that the tool is switched off.

Spraying

CAUTION:

•To prevent sudden spraying, be sure to set the lever cock to STOP, before turning sprayer switch ON or OFF.

•When spray work is interrupted, be sure to turn switch OFF, to prevent inadvertent spraying. (Fig. 4)

Be sure to check the situation of surroundings before turning sprayer switch ON.

BVF104, BVF154 specifications

Makita BVF154 and BVF104 are two powerful models in the realm of industrial-grade vacuum cleaners, designed to meet the needs of both professionals and DIY enthusiasts. These models stand out for their efficiency, performance, and user-friendly features, offering a solution for a variety of cleaning tasks, from job sites to workshops.

The Makita BVF154 is renowned for its robust performance, featuring a powerful motor that delivers impressive suction capabilities. This model is ideal for heavy-duty applications, making it a favorite among contractors and tradespeople. One of the key features of the BVF154 is its large capacity dust bag that minimizes the frequency of replacements, allowing users to work uninterrupted. Additionally, it has a compact design that makes it easy to maneuver and transport, catering to the dynamic needs of job sites.

On the other hand, the BVF104 is designed for lighter tasks while still maintaining an excellent suction power. It is particularly suited for smaller jobs such as cleaning up fine dust or debris from woodworking projects. The BVF104 features a lightweight construction that enhances portability, making it easy to carry around. This model is also equipped with an adjustable suction control, allowing users to fine-tune the power based on the specific cleaning task at hand.

Both models incorporate advanced filtration systems designed to capture fine particles, ensuring a cleaner environment and reducing the risk of respiratory issues for users. The easy-to-clean filter systems enhance the longevity of the vacuum and maintain optimal performance over time.

In terms of user comfort, both the BVF154 and BVF104 have ergonomically designed handles for better grip and control, minimizing user fatigue during extended use. These vacuums also come with various attachments such as crevice tools and brush heads, enhancing their versatility for different surfaces and cleaning tasks.

Among the technologies utilized in these models, the incorporation of Makita's Star Protection Computer Controls technology helps to prevent damage from overloading, over-discharging, or overheating. This not only extends the lifespan of the vacuum but also ensures safety during operation.

In summary, the Makita BVF154 and BVF104 are exemplary models characterized by their powerful performance, user-friendly features, and effective filtration systems. Whether for heavy-duty cleaning tasks or lighter applications, these vacuums offer reliability and efficiency that professionals and hobbyists can depend on.