Graco PRO Xs4 AA manual Power Supply Removal and Replacement, Power Supply and Turbine Alternator

Page 33

Power Supply Removal and Replacement

NOTE:

•Inspect the gun handle power supply cavity for dirt or moisture. Clean with a clean, dry rag.

•Do not expose gasket (10) to solvents.

1.Prepare gun for service, page 26.

2.Remove the barrel (16), page 32.

CAUTION

Be careful when handling the power supply (18) to avoid damaging it.

Repair

7.Connect the 3-wire connector (B). Slide the alterna- tor (19) down onto the power supply (18).

8.Lubricate the alternator o-ring (19a*) with non-sili- cone grease, Part No. 111265. Do not over-lubricate.

9.Lubricate the power supply o-ring (18a*) with dielectric grease (40).

10.Insert the power supply/alternator assembly in the gun handle (17). Make sure the ground strips make contact with the handle. On Smart Models only, con- nect the flexible circuit (59) to the socket at the top of the handle. Push the 6-pin connector into the socket to ensure it is properly connected.

11.Install the barrel (16), page 32.

12.Test gun resistance, page 19.

3.Grasp the power supply (18) with your hand. With a gentle side to side motion, free the power supply/ alternator assembly from the gun handle (17), then carefully pull it straight out. On Smart Models only, disconnect the flexible circuit (59) from the socket at the top of the handle (17). See Fig. 17.

4.Disconnect the 3-wire connector (B) from the power supply. Slide the alternator up and off the power supply. Inspect the power supply and alternator for damage. On Smart Models only, disconnect the 6-pin flexible circuit (59) from the power supply.

5.Check the power supply resistance, page 20. Replace if necessary.

NOTE: Before installing the power supply, make sure the o-rings (18a*, 19a*), spring (18b), and pads (19e) are in place.

6.On Smart Models only, connect the 6-pin flexible cir- cuit (59) to the power supply.

17

*10

*19a

19

19e

B

59

ti1505c

 

18

18b

*18a

Fig. 17. Power Supply and Turbine Alternator

309295

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Instructions Parts List 309295 This manual contains important warnings and informationStandard Model Table of Contents Symbols List of ModelsModel Description Operation Fire, Explosion, and Electric Shock Hazard Toxic Fluid Hazard Fluid Injection HazardEquipment Misuse Hazard How the Electrostatic AA Spray Gun Works Introduction= on = OFF Gun OverviewStandard Gun Smart GunInstall the System InstallationVentilate the Spray Booth Flammable or Toxic Vapor HazardHazardous Area Non-Hazardous AreaConnect the Air Line Connect the Exhaust TubeElectric Shock Hazard Select a Spray Tip Connect the Fluid LineGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Viscosity Check Fluid ResistivityOperation Low Voltage Adjustment Smart Guns OnlyFlush the Spray Gun MaintenanceTi1465a Test Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceTroubleshooting Spray Pattern TroubleshootingProblem Cause Solution Gun Operation Troubleshooting Electrical Troubleshooting Repair Pressure Relief ProcedureTools Needed Prepare the Gun for ServiceTip Guard, Air Cap, and Spray Tip Replace- ment Tip Guard, Air Cap, Spray Tip, or Seat Housing ReplacementRepair Electrode Replacement Electrode ReplacementFluid Filter Removal Fluid Tube ReplacementSpring Cap and Springs Fluid Needle ReplacementBarrel Removal Barrel InstallationPower Supply and Turbine Alternator Power Supply Removal and ReplacementTurbine Alternator Removal and Replacement Atomizing Air Adjustment Valve Atomizing Air Adjustment Valve RepairAir Valve Air Valve RepairES ON/OFF Valve ES ON/OFF Valve RepairPart No 85 kV Electrostatic Gun, Series a items PartsRef. No Atomizing Air Adjustment Valve Ref. No AlternatorRef. No ES ON/OFF Valve AIR CAP Description QtyIncluded in Air Seal Repair Kit 53 Ref Adjustment valve 20, and ES ON/OFF valveRef. No Alternator Description Qty SWITCH, ES HI/LO Accessories Air Line AccessoriesFluid Line Accessories Miscellaneous Accessories Gun AccessoriesFan Width at Orifice Size Spray Tip Selection ChartCategory Data Technical DataGraco Standard Warranty Graco Phone NumbersToll Free

PRO Xs4 AA specifications

The Graco PRO Xs4 AA is an advanced airless paint sprayer known for its superior performance and versatility, making it ideal for professionals and DIY enthusiasts alike. This sprayer is designed to handle a wide range of coatings, including latex, stains, and heavy-bodied materials, providing exceptional finish quality on various surfaces.

One of the standout features of the PRO Xs4 AA is its powerful TrueAirless technology, which ensures a consistent and even spray pattern. This technology allows users to achieve a professional finish without the need for thinning materials, saving time and effort. The sprayer is equipped with a robust 0.75 HP motor, delivering up to 0.40 GPM (gallons per minute) fluid output, making it suitable for medium to large-sized projects.

Another significant characteristic is the PRO Xs4's lightweight design, making it easy to transport and maneuver while working. Weighing only 34 pounds, it is simple to set up and operate, reducing fatigue during extended use. The unit features an adjustable pressure settings system, allowing users to control the flow rate according to their specific job requirements for optimal results.

The Graco PRO Xs4 AA also comes with the innovative Graco BlueLink technology, which provides real-time monitoring and diagnostics through a Bluetooth connection. This feature enables users to track their job performance, receive maintenance reminders, and access operational data directly from their smartphones, enhancing user experience and efficiency.

Additionally, the PRO Xs4 is equipped with a durable 515 spray tip, designed to create a fine finish while minimizing overspray. The inclusion of the FlexLiner bag system allows for quick color changes and easy cleanup, making it a truly user-friendly tool. The sprayer is also compatible with a variety of Graco accessories, allowing for customization and improved efficiency based on project needs.

With a maximum tip size of 0.017 inches, the PRO Xs4 is versatile enough to handle both fine and coarse coatings, making it a great option for a range of applications, from interior walls to exterior surfaces. The Graco PRO Xs4 AA combines cutting-edge technology with ease of use, making it an excellent choice for anyone looking to achieve professional-quality results in their painting projects.
Top Page Image Contents