Graco PRO Xs4 AA manual Gun Accessories, Miscellaneous Accessories

Page 47

Gun Accessories

Gun Repair Kit

244781 Air Seal Repair Kit

Electrode Replacement Kit

244917 Includes five electrodes.

Inline Fluid Filters

238561 100 mesh filter. Set of three.

238563 60 mesh filter. Set of three.

Round Pattern Kit

Provides higher level of performance to electrostatic spraying.

245282 Includes tip of choice.

Accessories

Alternator Bearing Kit

223688 To repair the turbine alternator.

Cleaning Brush

105749 For cleaning air cap and fluid nozzle.

Miscellaneous Accessories

Ground Wire and Clamp

222011 For grounding pump and other compo- nents and equipment in the spray area. 12 gauge, 25 ft (7.6 m).

Megohmmeter

241079 500 Volt output; 0.01-2000 megohms.

Not for use in hazardous areas.

ES Always On Kit

244913 Replaces inlet fitting with ball valve to shut off air during flushing. Converts ES ON/ OFF valve to always ON condition.

Paint Resistance Meter

722886 Use with 722860 Paint Probe to measure resistance of paint.

Not for use in hazardous areas.

Handle Grips

245263	Medium Grip
245264	Large Grip

Gun Washer Kit

245271 Use to convert Graco gun washers so they can clean PRO Xs4 air-assisted spray guns.

Gun Valve Lubricant

111265 4 oz (113 g) tube of sanitary (non-silicone) lubricant for fluid seals and wear areas.

Paint Probe

722860 Use with 722886 Paint Resistance Meter to measure resistance of paint.

Not for use in hazardous areas.

Safety Warning Sign

180060 English Warning Sign. FM Approved. Available at no charge from Graco.

Instruction Signs

198310 English Setup Instructions.

198320 English Daily Care Instructions.

309295

47

Image 47

Contents Standard Model Instructions Parts List 309295This manual contains important warnings and information Table of Contents Model Description Operation SymbolsList of Models Fire, Explosion, and Electric Shock Hazard Toxic Fluid Hazard Fluid Injection HazardEquipment Misuse Hazard How the Electrostatic AA Spray Gun Works IntroductionSmart Gun Gun Overview= on = OFF Standard GunFlammable or Toxic Vapor Hazard InstallationInstall the System Ventilate the Spray BoothHazardous Area Non-Hazardous AreaElectric Shock Hazard Connect the Air LineConnect the Exhaust Tube Select a Spray Tip Connect the Fluid LineGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Viscosity Check Fluid ResistivityOperation Low Voltage Adjustment Smart Guns OnlyFlush the Spray Gun MaintenanceTi1465a Test Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceProblem Cause Solution TroubleshootingSpray Pattern Troubleshooting Gun Operation Troubleshooting Electrical Troubleshooting Repair Pressure Relief ProcedureTools Needed Prepare the Gun for ServiceTip Guard, Air Cap, and Spray Tip Replace- ment Tip Guard, Air Cap, Spray Tip, or Seat Housing ReplacementRepair Electrode Replacement Electrode ReplacementFluid Filter Removal Fluid Tube ReplacementSpring Cap and Springs Fluid Needle ReplacementBarrel Removal Barrel InstallationPower Supply and Turbine Alternator Power Supply Removal and ReplacementTurbine Alternator Removal and Replacement Atomizing Air Adjustment Valve Atomizing Air Adjustment Valve RepairAir Valve Air Valve RepairES ON/OFF Valve ES ON/OFF Valve RepairPart No 85 kV Electrostatic Gun, Series a items PartsRef. No ES ON/OFF Valve Ref. No Atomizing Air Adjustment ValveRef. No Alternator AIR CAP Description QtyIncluded in Air Seal Repair Kit 53 Ref Adjustment valve 20, and ES ON/OFF valveRef. No Alternator Description Qty SWITCH, ES HI/LO Fluid Line Accessories AccessoriesAir Line Accessories Miscellaneous Accessories Gun AccessoriesFan Width at Orifice Size Spray Tip Selection ChartCategory Data Technical DataToll Free Graco Standard WarrantyGraco Phone Numbers