Graco PRO Xs4 AA manual Fluid Injection Hazard, Toxic Fluid Hazard

Page 5

Warning

WARNING

Fluid Injection Hazard

Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin can also cause serious injury.

Fluid injected into the skin might look like just a cut, but is a serious injury. Get immediate medical attention.

Do not point the gun at anyone or at any part of the body. Do not put your hand or fingers over the spray tip. Do not stop or deflect fluid leaks with your hand, body, glove, or rag.

Never spray without the tip guard in place.

Lock the trigger safety when you stop spraying.

Follow the “Pressure Relief Procedure”, page 25, when you stop spraying and before clean- ing, checking, or repairing equipment.

Check the hoses and couplings daily. Replace worn, damaged, or loose parts immediately. Per- manently coupled hoses cannot be repaired; replace the entire hose.

Tighten all fluid connections before each use.

Toxic Fluid Hazard

Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the skin, swallowed, or inhaled.

Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

Store hazardous fluid in an approved container. Dispose of the hazardous fluid according to all local, state, and national guidelines.

Wear appropriate protective clothing, gloves, eyewear, and respirator.

309295

5

Image 5
Contents Standard Model Instructions Parts List 309295This manual contains important warnings and information Table of Contents Model Description Operation SymbolsList of Models Fire, Explosion, and Electric Shock Hazard Toxic Fluid Hazard Fluid Injection HazardEquipment Misuse Hazard How the Electrostatic AA Spray Gun Works Introduction= on = OFF Gun OverviewStandard Gun Smart GunInstall the System InstallationVentilate the Spray Booth Flammable or Toxic Vapor HazardHazardous Area Non-Hazardous AreaElectric Shock Hazard Connect the Air LineConnect the Exhaust Tube Select a Spray Tip Connect the Fluid LineGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Viscosity Check Fluid ResistivityOperation Low Voltage Adjustment Smart Guns OnlyFlush the Spray Gun MaintenanceTi1465a Test Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceProblem Cause Solution TroubleshootingSpray Pattern Troubleshooting Gun Operation Troubleshooting Electrical Troubleshooting Repair Pressure Relief ProcedureTools Needed Prepare the Gun for ServiceTip Guard, Air Cap, and Spray Tip Replace- ment Tip Guard, Air Cap, Spray Tip, or Seat Housing ReplacementRepair Electrode Replacement Electrode ReplacementFluid Filter Removal Fluid Tube ReplacementSpring Cap and Springs Fluid Needle ReplacementBarrel Removal Barrel InstallationPower Supply and Turbine Alternator Power Supply Removal and ReplacementTurbine Alternator Removal and Replacement Atomizing Air Adjustment Valve Atomizing Air Adjustment Valve RepairAir Valve Air Valve RepairES ON/OFF Valve ES ON/OFF Valve RepairPart No 85 kV Electrostatic Gun, Series a items PartsRef. No ES ON/OFF Valve Ref. No Atomizing Air Adjustment ValveRef. No Alternator AIR CAP Description QtyIncluded in Air Seal Repair Kit 53 Ref Adjustment valve 20, and ES ON/OFF valveRef. No Alternator Description Qty SWITCH, ES HI/LO Fluid Line Accessories AccessoriesAir Line Accessories Miscellaneous Accessories Gun AccessoriesFan Width at Orifice Size Spray Tip Selection ChartCategory Data Technical DataToll Free Graco Standard WarrantyGraco Phone Numbers