Graco 130HS important safety instructions Hydraulic Pump, Removal, Installation

Page 11

Hydraulic Pump

Removal

1.Allow hydraulic system to cool before beginning ser- vice.

2.Relieve pressure, page 7.

3.Place drip pan or rags under sprayer to catch hydraulic oil that leaks out during repair.

4.Remove drain plug (195) and oil filter (199) and allow hydraulic oil to drain.

5.Remove screw (224), loosen belt guard knob (241) and belt guard (24).

6.Raise motor and remove belt (143).

7.Remove two set screws (169) and fan pulley (86).

8.Remove case drain tube (251).

9.Remove elbow (182).

10.Loosen screw (184) and remove pressure control guard (63).

11.Loosen set screw (102) and remove remote pres- sure control cable (12).

12.Remove eight screws (184) and washers (101), res- ervoir cover (237), filter assembly (A) and gasket

13.Remove four screws (215) and o-rings (178), o-ring

(180)and hydraulic pump (252) from reservoir cover

(237).

Hydraulic Pump

Installation

1.Install hydraulic pump (252) on reservoir cover (237) with four screws (215) and o-rings (178), o-ring (180); torque 100 in-lb (11 N·m).

2.Install gasket (85) filter assembly (A) and reservoir cover (237) with eight washers (101) and screws (184); torque 90 in-lb (10 N•m).

3.Install elbow (182) per instructions, page 6; torque to 15 ft-lb (20.3 N•m).

4.Install pressure control guard (63) and tighten screw (184).

5.Connect hydraulic hoses (32) and (35).

6.Install case drain tube (251); torque to 15 ft-lb (20.3 N•m).

7.Install fan pulley (86) with two set screws (193).

8.Raise motor and install belt (143).

9.Install belt guard (24) with screw (224) and belt guard knob (241).

10.Install remote pressure control cable (12).Tighten set screw (102).

11.Install drain plug (195); torque to 110 in-lb (12.4 N•m). Install oil filter (199); tighten 3/4 turn after gasket contacts base. Fill with Graco hydraulic oil, page 7.

12.Start up and allow pump to operate at low pressure for approximately 5 minutes to purge all air.

13.Check and top off hydraulic oil level.

313776G

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents LineLazer 130 HS Contents Fire and Explosion Hazard Equipment Misuse Hazard Tip Selection Grounding SAE O-Ring InstallationGeneral Repair Information Caster Wheel MaintenancePressure Relief Procedure Problem Cause Solution TroubleshootingOr worn and that ball seats well. Reassemble Displacement pump outlet filter if used is dirty or Removal InstallationHydraulic Pump 195 Fan Belt Engine Do Fan Belt, InstallationHydraulic Motor Yoke Ti13918a Oil/Filter Change Remove suction tube 34 and hose Displacement PumpLineLazer IV 130HS Parts290 Part Description Qty Detail Torque to 90-110 in-lb Torque to 10-20 ft-lb Parts LineLazer IV 130HS Screw 138 231 Kits 193 Washer Detail a JAW Accessories Technical Data313776G Graco Information Graco Standard Warranty

130HS specifications

The Graco 130HS is a highly regarded airless paint sprayer, designed to meet the demands of both professionals and DIY enthusiasts. This versatile tool excels in providing smooth, even coverage across a variety of surfaces, making it an essential addition to any painting arsenal.

One of the primary features of the Graco 130HS is its robust performance capabilities. It boasts a powerful motor that can handle a wide range of materials, from thin stains to thicker paints. This flexibility allows users to tackle a variety of projects, including residential and commercial applications. The sprayer has a maximum pressure rating of 3000 PSI, which ensures that it can atomize even the most challenging coatings, delivering a consistent finish.

Another standout characteristic of the Graco 130HS is its LightSpeed technology, which optimizes spray patterns and reduces overspray. This feature not only saves material but also enhances precision, making it easier to paint intricate surfaces without the worry of unintended coverage. The adjustable pressure settings give users the ability to control the flow of paint, further allowing for customization based on the specific project requirements.

The Graco 130HS also incorporates a durable build quality that's designed for long-term use. Constructed with high-grade materials, it can withstand the rigors of day-to-day operation on various job sites. Its compact and portable design makes it easy to transport, enabling users to move from one project location to another with ease.

Moreover, the user-friendly interface features a simple setup process, allowing for quick preparation and less downtime before work begins. The spray tip system is designed for easy swapping, providing versatility in achieving different spray patterns and finishes.

In conclusion, the Graco 130HS airless paint sprayer is an efficient, reliable tool that brings professional-grade performance to both seasoned painters and novices alike. With its powerful motor, innovative technologies, and durable construction, it stands out in the market, ensuring that every project is completed with precision and ease. Whether you’re painting a room, a fence, or undertaking a larger renovation, the Graco 130HS provides the capability and reliability needed to achieve stunning results.
Top Page Image Contents