Graco Inc PRO Auto Xs AA Install the Air Line Accessories, Install the Fluid Line Accessories

Page 11

Install the Air Line

Accessories

WARNING

Component Rupture Hazard

To reduce the risk of serious injury due to component rupture:

The pump pressure must be limited by the pump air regulator. Do not rely on the gun fluid regulator to limit the fluid pressure to the gun.

The fluid supply pump must be prevented from pro- ducing a fluid pressure greater than the 3000 psi (21 MPa, 210 bar) Maximum Working Fluid Pressure of the gun. For example, the air supply pressure to a 30:1 ratio pump must not exceed 100 psi (0.7 MPa, 7 bar).

Be sure that all spray equipment and accessories added to the spray system are properly rated to with- stand the maximum working pressure of your system.

1.Install a bleed-type master air valve (L) on the main air line (W) to shut off all air to the gun (H).

2.Install an air line filter/water separator on the gun air line to ensure a dry, clean air supply to the gun. Dirt and moisture can ruin the appearance of your fin- ished workpiece and can cause the gun to malfunc- tion.

3.Install a bleed-type air regulator (M) on each of the air supply lines (B, C, E, X, Y) to control air pressure to the gun.

4.Install a solenoid valve (K) on the cylinder air line (E) to actuate the gun. The solenoid valve must have a quick exhaust port.

5.Install a bleed-type master air valve (L) on each pump air line to shut off all air to the pump (H).

Installation

WARNING

Skin Injection Hazard

Trapped air can cause the gun to spray unexpectedly, which can result in serious

injury, including injecting fluid through the skin. The solenoid valves (K) must have a quick exhaust port so trapped air will be relieved between the valve and gun when the solenoids are shut off. The bleed-type master air valve (L) is required on the pump air line so trapped air will be relieved between the valve and the pump after the valves or regulator are closed.

Install the Fluid Line

Accessories

1.Install a fluid filter and drain valve at the pump out- let. Filtering the fluid will help remove coarse parti- cles and sediment that could clog the spray tip.

The gun includes an inline fluid filter (20) for addi- tional filtration.

WARNING

Skin Injection Hazard

The fluid drain valve is required in your sys- tem to assist in relieving fluid pressure in

the displacement pump, hose and gun. Trig- gering the gun to relieve pressure may not be suffi- cient. Install a drain valve close to the pump's fluid outlet. The drain valve reduces the risk of serious injury, including fluid injection and splashing in the eyes or on the skin.

2.Install a fluid regulator on the fluid line to control fluid pressure to the gun.

309298J

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents II 2 G EEx 0.24MJ Instructions/Parts ListImportant Safety Instructions See page 2 for Table of ContentsTable of Contents Fire, Explosion, and Electric Shock Hazard SymbolsToxic Fluid Hazard Skin Injection HazardEquipment Misuse Hazard Operating the Spray Function Gun Features and OptionsIntroduction How the Electrostatic AA Spray Gun WorksKV1 Air KV2 Air Output Voltage kV Changing the kV SettingKV1 and KV2 Switch Settings Manifold Markings TI1714A Manifold Back ViewVentilate the Spray Booth InstallationInstall the System Non-Hazardous Area Non-Hazardous Area Manifold Back ViewSkin Injection Hazard Install the Air Line AccessoriesInstall the Fluid Line Accessories Component Rupture HazardMounting Bracket Install the Gun and Mounting BracketSupply Hose Connect the Air and Fluid LinesManifold Connections Electric Shock HazardFiber Optic Fitting Optional Fiber Optic Cable ConnectionGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Viscosity Install the Fabric CoverCheck Fluid Resistivity Operation Pressure Relief ProcedureOperating Checklist Relief Procedure at leftSelect a Spray Tip Install the Spray TipCorrect Set the Atomization Fluid PressurePressurized Equipment Hazard Psi 21 MPa, 210 barTurbine Air Air pressure at turbine air hose Hose Length Adjust the ElectrostaticsDynamic Turbine Air Pressures Fire and Explosion Hazard SprayingTriggering the Fluid Alone ShutdownDo not immerse the gun in fluid MaintenanceDaily Care and Cleaning Do not point the gun up while cleaning itFire, Explosion, and Electric Shock Hazard Remove Spray Tip Before Flushing Flush the Spray GunEquipment Needed Clean the Spray GunProcedure Clean the Inline Fluid Filter Check for Fluid Leakage Skin Injection Hazard Check for Fluid LeakageTest Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceSpray Pattern Troubleshooting TroubleshootingGun Operation Troubleshooting 16 and Test Gun Resistance Electrical TroubleshootingSee Test Gun Resistance on See Check Electrical Grounding onRepair Prepare the Gun for ServiceRemove the Gun from the Manifold Install the Gun on the ManifoldTip Guard, Air Cap, and Spray Tip Replace- ment Tip Guard, Air Cap, Spray Tip, or Seat Housing ReplacementRepair Electrode Replacement Electrode ReplacementFluid Filter Removal Fluid Tube ReplacementNot overtighten Fluid Needle ReplacementPiston O-Rings Piston RepairActuator Arm Adjustment Adjust the Actuator ArmBarrel Removal Barrel RemovalBarrel Installation Barrel InstallationPower Supply Removal and Replacement Power Supply Turbine Alternator Removal and ReplacementRef. No Alternator Detail PartsPart No PRO Auto Xs AA Electrostatic Gun, Series a Description Qty Plug Fan Width at Orifice Size Spray Tip Selection ChartFluid Line Accessories AccessoriesGun Accessories Air Line AccessoriesFiber Optic Y Cables Safety Warning SignsPaint Probe ES Display ModuleAccessories 309298J Category Data Technical DataToll Free Graco Standard WarrantyGraco Information

244592, PRO Auto Xs AA, TI1713A, 309298J specifications

Graco Inc is a renowned brand in the field of fluid handling systems and accessories, with a reputation for delivering high-quality products that serve a variety of industries, including automotive, construction, and manufacturing. Among their extensive lineup, the Graco 309298J, TI1713A, PRO Auto Xs AA, 244592 represents a significant advancement in spray technology, notably regarded for its efficiency and versatility.

The Graco 309298J model is a part of the PRO Auto Xs series, designed specifically for high-performance spray applications. One of the standout features of this equipment is its auto-adjusting technology, which automatically adapts the spray pattern based on the surface being coated. This ensures uniform coverage and reduces the waste of material, making it an environmentally friendly option.

Equipped with an ergonomic design, the PRO Auto Xs AA enhances user comfort and reduces fatigue during prolonged use. The lightweight construction makes it easy to handle, while the balanced design allows for precise control, ensuring that even intricate spray patterns can be achieved with minimal effort.

Technologically, this spray gun incorporates advanced fluid dynamics that allow it to produce fine atomization, resulting in a superior finish. The easy-to-clean design coupled with a durable construction ensures that maintenance is straightforward, which is crucial for professionals who require reliability under demanding conditions.

Another notable characteristic is the Graco TI1713A tip, which is compatible with a variety of coatings, including paint, stains, and sealers. This versatility allows users to switch seamlessly between different materials without the need for extensive reconfiguration. The adjustability of the spray width further adds to its functionality, enabling operators to customize the application based on the job requirements.

Additionally, the 244592 model is designed with safety features, such as anti-drip mechanisms and pressure control valves, ensuring safe operation. Graco's commitment to quality is evident in the durability of its products, as they withstand the rigors of daily use while delivering consistent performance over time.

In summary, the Graco 309298J Pro Auto Xs AA, 244592 is a sophisticated spray solution that showcases the fusion of advanced technology and user-centric design, catering to professionals seeking efficiency, versatility, and reliability in their spray applications. This model stands out as an essential tool for anyone looking to enhance their workflow and achieve exceptional finish quality.
Top Page Image Contents