Graco Inc 244592, 309298J, TI1713A Flush the Spray Gun, Remove Spray Tip Before Flushing

Page 25

Flush the Spray Gun

WARNING

Skin Injection Hazard

To reduce the risk of a fluid injection injury, always follow the Pressure Relief Proce- dure on page 18 when you stop spraying and whenever you are instructed to relieve the pressure.

1. Relieve the pressure.

WARNING

Fire, Explosion, and Electric Shock Hazard

To reduce the risk of fire, explosion, or elec-

Maintenance

3.Remove the retaining ring (1), tip guard (3), air cap (40), spray tip (4), and gun shroud (2). See FIG. 14.. Clean these parts and set them aside.

4.Turn on the solvent supply. Use the lowest possible fluid pressure when flushing.

5.Turn on the cylinder air (CYL) to trigger the gun.

6.Flush the gun, spraying into a grounded metal con- tainer until clean solvent comes from the gun.

7.Turn off the solvent supply.

8.Relieve the pressure.

9.Install the spray tip (4) and air cap (40), tip guard (3), shroud (2), and retaining ring (1) onto the gun. Tighten the retaining ring firmly.

2

4a

4

tric shock, turn off the turbine air (TA) before flushing the gun or any part of the system.

2. Be sure the turbine air (TA) is turned off.

40

3

1a

1

TI1723A

Fig. 14. Remove Spray Tip Before Flushing

309298J

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Important Safety Instructions Instructions/Parts ListSee page 2 for Table of Contents II 2 G EEx 0.24MJTable of Contents Fire, Explosion, and Electric Shock Hazard SymbolsToxic Fluid Hazard Skin Injection HazardEquipment Misuse Hazard Introduction Gun Features and OptionsHow the Electrostatic AA Spray Gun Works Operating the Spray FunctionKV1 and KV2 Switch Settings Changing the kV SettingKV1 Air KV2 Air Output Voltage kV Manifold Markings TI1714A Manifold Back ViewInstall the System InstallationVentilate the Spray Booth Non-Hazardous Area Non-Hazardous Area Manifold Back ViewInstall the Fluid Line Accessories Install the Air Line AccessoriesComponent Rupture Hazard Skin Injection HazardMounting Bracket Install the Gun and Mounting BracketManifold Connections Connect the Air and Fluid LinesElectric Shock Hazard Supply HoseFiber Optic Fitting Optional Fiber Optic Cable ConnectionGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Resistivity Install the Fabric CoverCheck Fluid Viscosity Operating Checklist Pressure Relief ProcedureRelief Procedure at left OperationSelect a Spray Tip Install the Spray TipPressurized Equipment Hazard Set the Atomization Fluid PressurePsi 21 MPa, 210 bar CorrectDynamic Turbine Air Pressures Adjust the ElectrostaticsTurbine Air Air pressure at turbine air hose Hose Length Triggering the Fluid Alone SprayingShutdown Fire and Explosion HazardDaily Care and Cleaning MaintenanceDo not point the gun up while cleaning it Do not immerse the gun in fluidFire, Explosion, and Electric Shock Hazard Remove Spray Tip Before Flushing Flush the Spray GunProcedure Clean the Spray GunEquipment Needed Clean the Inline Fluid Filter Check for Fluid Leakage Skin Injection Hazard Check for Fluid LeakageTest Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceSpray Pattern Troubleshooting TroubleshootingGun Operation Troubleshooting See Test Gun Resistance on Electrical TroubleshootingSee Check Electrical Grounding on 16 and Test Gun ResistanceRepair Prepare the Gun for ServiceRemove the Gun from the Manifold Install the Gun on the ManifoldTip Guard, Air Cap, and Spray Tip Replace- ment Tip Guard, Air Cap, Spray Tip, or Seat Housing ReplacementRepair Electrode Replacement Electrode ReplacementFluid Filter Removal Fluid Tube ReplacementNot overtighten Fluid Needle ReplacementPiston O-Rings Piston RepairActuator Arm Adjustment Adjust the Actuator ArmBarrel Removal Barrel RemovalBarrel Installation Barrel InstallationPower Supply Removal and Replacement Power Supply Turbine Alternator Removal and ReplacementPart No PRO Auto Xs AA Electrostatic Gun, Series a PartsRef. No Alternator Detail Description Qty Plug Fan Width at Orifice Size Spray Tip Selection ChartGun Accessories AccessoriesAir Line Accessories Fluid Line AccessoriesPaint Probe Safety Warning SignsES Display Module Fiber Optic Y CablesAccessories 309298J Category Data Technical DataGraco Information Graco Standard WarrantyToll Free

244592, PRO Auto Xs AA, TI1713A, 309298J specifications

Graco Inc is a renowned brand in the field of fluid handling systems and accessories, with a reputation for delivering high-quality products that serve a variety of industries, including automotive, construction, and manufacturing. Among their extensive lineup, the Graco 309298J, TI1713A, PRO Auto Xs AA, 244592 represents a significant advancement in spray technology, notably regarded for its efficiency and versatility.

The Graco 309298J model is a part of the PRO Auto Xs series, designed specifically for high-performance spray applications. One of the standout features of this equipment is its auto-adjusting technology, which automatically adapts the spray pattern based on the surface being coated. This ensures uniform coverage and reduces the waste of material, making it an environmentally friendly option.

Equipped with an ergonomic design, the PRO Auto Xs AA enhances user comfort and reduces fatigue during prolonged use. The lightweight construction makes it easy to handle, while the balanced design allows for precise control, ensuring that even intricate spray patterns can be achieved with minimal effort.

Technologically, this spray gun incorporates advanced fluid dynamics that allow it to produce fine atomization, resulting in a superior finish. The easy-to-clean design coupled with a durable construction ensures that maintenance is straightforward, which is crucial for professionals who require reliability under demanding conditions.

Another notable characteristic is the Graco TI1713A tip, which is compatible with a variety of coatings, including paint, stains, and sealers. This versatility allows users to switch seamlessly between different materials without the need for extensive reconfiguration. The adjustability of the spray width further adds to its functionality, enabling operators to customize the application based on the job requirements.

Additionally, the 244592 model is designed with safety features, such as anti-drip mechanisms and pressure control valves, ensuring safe operation. Graco's commitment to quality is evident in the durability of its products, as they withstand the rigors of daily use while delivering consistent performance over time.

In summary, the Graco 309298J Pro Auto Xs AA, 244592 is a sophisticated spray solution that showcases the fusion of advanced technology and user-centric design, catering to professionals seeking efficiency, versatility, and reliability in their spray applications. This model stands out as an essential tool for anyone looking to enhance their workflow and achieve exceptional finish quality.
Top Page Image Contents