Graco Inc 309298J, 244592, TI1713A, PRO Auto Xs AA Fluid Tube Replacement, Fluid Filter Removal

Page 40

Repair

Fluid Tube Replacement

There are no replaceable parts in the fluid tube assem- bly. Only remove when necessary.

1.Prepare the gun for service, page 35.

2.Remove the air cap assembly, page 37. Remove the shroud (2).

3.Disconnect the bottom fluid tube nut (C). See FIG. 26..

4.Carefully unscrew the top fluid tube nut (D).

C

20

E

D

ti1524a

Fig. 26. Fluid Tube Replacement

CAUTION

Be careful not to damage the fluid tube assembly (19) when cleaning or installing it, especially the sealing surface (E). If the sealing surface is damaged, the entire fluid tube assembly must be replaced.

5.Apply Part No. 116553 dielectric grease to the entire length of the plastic extension on the end of the fluid tube (19).

6.Apply low strength thread sealant to the fluid tube nut threads.

7.Install the fluid tube into the gun barrel and tighten the top nut (D) hand-tight, then 1/4 to 1/2 turn with a wrench. There will be a gap between the nut and barrel. Do not overtighten the nut.

8.Make sure the fluid filter (20) is in place. Tighten the bottom nut (C) onto the fitting (22) and torque to

20-30 in-lb (2.3-3.4 N•m). Make sure the top nut remains tight.

9.Reinstall the shroud and air cap assembly, page 37.

10.Test gun resistance, page 29.

Fluid Filter Removal

1.Prepare the gun for service, page 35.

2.Remove the air cap assembly, page 37. Remove the shroud (2).

3.Disconnect the bottom fluid tube nut (C).

4.Remove the fluid filter (20). Clean or replace the fil- ter, as needed.

Replacement filters are available in 100 mesh (stan- dard) or 60 mesh sizes. See page 52.

5.Install the fluid filter. Tighten the bottom nut (C) onto the fitting (22) and torque to 20-30 in-lb (2.3-3.4 N•m). Make sure the top nut (D) remains tight.

CAUTION

Be sure the fluid tube (19) is not twisted after tighten- ing the bottom nut (C).

6.Reinstall the shroud and air cap assembly, page 37.

7.Test gun resistance, page 29.

40

309298J

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Instructions/Parts List Important Safety InstructionsSee page 2 for Table of Contents II 2 G EEx 0.24MJTable of Contents Symbols Fire, Explosion, and Electric Shock HazardSkin Injection Hazard Toxic Fluid HazardEquipment Misuse Hazard Gun Features and Options IntroductionHow the Electrostatic AA Spray Gun Works Operating the Spray FunctionKV1 and KV2 Switch Settings Changing the kV SettingKV1 Air KV2 Air Output Voltage kV TI1714A Manifold Back View Manifold MarkingsInstall the System InstallationVentilate the Spray Booth Non-Hazardous Area Manifold Back View Non-Hazardous AreaInstall the Air Line Accessories Install the Fluid Line AccessoriesComponent Rupture Hazard Skin Injection HazardInstall the Gun and Mounting Bracket Mounting BracketConnect the Air and Fluid Lines Manifold ConnectionsElectric Shock Hazard Supply HoseOptional Fiber Optic Cable Connection Fiber Optic FittingGrounding Check Electrical Grounding Check Gun GroundingCheck Fluid Resistivity Install the Fabric CoverCheck Fluid Viscosity Pressure Relief Procedure Operating ChecklistRelief Procedure at left OperationInstall the Spray Tip Select a Spray TipSet the Atomization Fluid Pressure Pressurized Equipment HazardPsi 21 MPa, 210 bar CorrectDynamic Turbine Air Pressures Adjust the ElectrostaticsTurbine Air Air pressure at turbine air hose Hose Length Spraying Triggering the Fluid AloneShutdown Fire and Explosion HazardMaintenance Daily Care and CleaningDo not point the gun up while cleaning it Do not immerse the gun in fluidFire, Explosion, and Electric Shock Hazard Flush the Spray Gun Remove Spray Tip Before FlushingProcedure Clean the Spray GunEquipment Needed Clean the Inline Fluid Filter Check for Fluid Leakage Check for Fluid Leakage Skin Injection HazardElectrical Tests Test Gun ResistanceTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceTroubleshooting Spray Pattern TroubleshootingGun Operation Troubleshooting Electrical Troubleshooting See Test Gun Resistance onSee Check Electrical Grounding on 16 and Test Gun ResistancePrepare the Gun for Service RepairInstall the Gun on the Manifold Remove the Gun from the ManifoldTip Guard, Air Cap, Spray Tip, or Seat Housing Replacement Tip Guard, Air Cap, and Spray Tip Replace- mentRepair Electrode Replacement Electrode ReplacementFluid Tube Replacement Fluid Filter RemovalFluid Needle Replacement Not overtightenPiston Repair Piston O-RingsAdjust the Actuator Arm Actuator Arm AdjustmentBarrel Removal Barrel RemovalBarrel Installation Barrel InstallationPower Supply Removal and Replacement Turbine Alternator Removal and Replacement Power SupplyPart No PRO Auto Xs AA Electrostatic Gun, Series a PartsRef. No Alternator Detail Description Qty Plug Spray Tip Selection Chart Fan Width at Orifice SizeAccessories Gun AccessoriesAir Line Accessories Fluid Line AccessoriesSafety Warning Signs Paint ProbeES Display Module Fiber Optic Y CablesAccessories 309298J Technical Data Category DataGraco Information Graco Standard WarrantyToll Free

244592, PRO Auto Xs AA, TI1713A, 309298J specifications

Graco Inc is a renowned brand in the field of fluid handling systems and accessories, with a reputation for delivering high-quality products that serve a variety of industries, including automotive, construction, and manufacturing. Among their extensive lineup, the Graco 309298J, TI1713A, PRO Auto Xs AA, 244592 represents a significant advancement in spray technology, notably regarded for its efficiency and versatility.

The Graco 309298J model is a part of the PRO Auto Xs series, designed specifically for high-performance spray applications. One of the standout features of this equipment is its auto-adjusting technology, which automatically adapts the spray pattern based on the surface being coated. This ensures uniform coverage and reduces the waste of material, making it an environmentally friendly option.

Equipped with an ergonomic design, the PRO Auto Xs AA enhances user comfort and reduces fatigue during prolonged use. The lightweight construction makes it easy to handle, while the balanced design allows for precise control, ensuring that even intricate spray patterns can be achieved with minimal effort.

Technologically, this spray gun incorporates advanced fluid dynamics that allow it to produce fine atomization, resulting in a superior finish. The easy-to-clean design coupled with a durable construction ensures that maintenance is straightforward, which is crucial for professionals who require reliability under demanding conditions.

Another notable characteristic is the Graco TI1713A tip, which is compatible with a variety of coatings, including paint, stains, and sealers. This versatility allows users to switch seamlessly between different materials without the need for extensive reconfiguration. The adjustability of the spray width further adds to its functionality, enabling operators to customize the application based on the job requirements.

Additionally, the 244592 model is designed with safety features, such as anti-drip mechanisms and pressure control valves, ensuring safe operation. Graco's commitment to quality is evident in the durability of its products, as they withstand the rigors of daily use while delivering consistent performance over time.

In summary, the Graco 309298J Pro Auto Xs AA, 244592 is a sophisticated spray solution that showcases the fusion of advanced technology and user-centric design, catering to professionals seeking efficiency, versatility, and reliability in their spray applications. This model stands out as an essential tool for anyone looking to enhance their workflow and achieve exceptional finish quality.
Top Page Image Contents