Graco Inc 309298J, 244592 Gun Accessories, Air Line Accessories, Fluid Line Accessories

Page 52
Includes tip of choice.

Accessories

Accessories

Gun Accessories

Electrode Replacement Kit

244917 Includes five electrodes.

Inline Fluid Filters

238561 100 mesh filter. Set of three.

238563 60 mesh filter. Set of three.

Round Pattern Kit

Provides higher level of performance to electrostatic spraying.

245298

Gun Valve Lubricant

111265 4 oz (113 g) tube of sanitary (non-silicone) lubricant for fluid seals and wear areas.

Alternator Bearing Kit

223688 To repair the turbine alternator.

Cleaning Brush

105749 For cleaning air cap and fluid nozzle.

Air Line Accessories

AirFlex™ Flexible Grounded Air Hose

100 psi (7 bar, 0.7 MPa) Maximum Working Pressure

0.315 in. (8 mm) ID; 1/4 npsm(f) x 1/4 npsm(f) left-hand thread

244963

6 ft (1.8 m)

244964

15 ft (4.6 m)

244965

25 ft (7.6 m)

244966

36 ft (11 m)

244967

50 ft (15 m)

244968

75 ft (23 m)

244969

100 ft (30.5 m)

Standard Grounded Air Hose (Grey)

100 psi (7 bar, 0.7 MPa) Maximum Working Pressure

0.315 in. (8 mm) ID; 1/4 npsm(f) x 1/4 npsm(f) left-hand thread

223068

6 ft (1.8 m)

223069

15 ft (4.6 m)

223070

25 ft (7.6 m)

223071

36 ft (11 m)

223072

50 ft (15 m)

223073

75 ft (23 m)

223074 100 ft (30.5 m)

Bleed-Type Master Air Valve

300 psi (21 bar, 2.1 MPa) Maximum Working Pressure

Relieves air trapped in the air line between this valve and the pump air motor when closed.

107141

3/4 npt

Air Line Shutoff Valve

150 psi (10 bar, 1.0 MPa) Maximum Working Pressure

For turning air to gun on or off.

224754 1/4 npsm(m) x 1/4 npsm(f) left-hand thread.

Fluid Line Accessories

Nylon Fluid Hose

3000 psi (210 bar, 21 MPa) Maximum Working Pressure

223540 1/4 in. (6 mm) ID x 25 ft (7.6 m), 1/4 npsm

223541 1/4 in. (6 mm) ID x 50 ft (15.2 m), 1/4 npsm

Fluid Shutoff/Drain Valve

5000 psi (350 bar, 35 MPa) Maximum Working Pressure

For turning fluid on or off to the gun and for relieving fluid line pressure at the pump.

210657 1/2 npt(m), fluoroelastomer seals

210658 3/8 npt(m), fluoroelastomer seals

210659 3/8 npt x 1/4 npt(m), fluoroelastomer seals

214037 1/4 npt(m), PTFE seals

Miscellaneous Accessories

Ground Wire and Clamp

222011 For grounding pump and other components and equipment in the spray area.

12 gauge, 25 ft (7.6 m).

Megohmmeter

241079 500 Volt output; 0.01-2000 megohms.

Not for use in hazardous areas.

Paint Resistance Meter

722886 Use with 722860 Paint Probe to measure resistance of paint.

Not for use in hazardous areas.

52

309298J

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Instructions/Parts List Important Safety InstructionsSee page 2 for Table of Contents II 2 G EEx 0.24MJTable of Contents Symbols Fire, Explosion, and Electric Shock HazardSkin Injection Hazard Toxic Fluid HazardEquipment Misuse Hazard Gun Features and Options IntroductionHow the Electrostatic AA Spray Gun Works Operating the Spray FunctionKV1 and KV2 Switch Settings Changing the kV SettingKV1 Air KV2 Air Output Voltage kV TI1714A Manifold Back View Manifold MarkingsInstall the System InstallationVentilate the Spray Booth Non-Hazardous Area Manifold Back View Non-Hazardous AreaInstall the Air Line Accessories Install the Fluid Line AccessoriesComponent Rupture Hazard Skin Injection HazardInstall the Gun and Mounting Bracket Mounting BracketConnect the Air and Fluid Lines Manifold ConnectionsElectric Shock Hazard Supply HoseOptional Fiber Optic Cable Connection Fiber Optic FittingGrounding Check Electrical Grounding Check Gun GroundingCheck Fluid Resistivity Install the Fabric CoverCheck Fluid Viscosity Pressure Relief Procedure Operating ChecklistRelief Procedure at left OperationInstall the Spray Tip Select a Spray TipSet the Atomization Fluid Pressure Pressurized Equipment HazardPsi 21 MPa, 210 bar CorrectDynamic Turbine Air Pressures Adjust the ElectrostaticsTurbine Air Air pressure at turbine air hose Hose Length Spraying Triggering the Fluid AloneShutdown Fire and Explosion HazardMaintenance Daily Care and CleaningDo not point the gun up while cleaning it Do not immerse the gun in fluidFire, Explosion, and Electric Shock Hazard Flush the Spray Gun Remove Spray Tip Before FlushingProcedure Clean the Spray GunEquipment Needed Clean the Inline Fluid Filter Check for Fluid Leakage Check for Fluid Leakage Skin Injection HazardElectrical Tests Test Gun ResistanceTest Power Supply Resistance Test Power Supply ResistanceTest Barrel Resistance Test Barrel ResistanceTroubleshooting Spray Pattern TroubleshootingGun Operation Troubleshooting Electrical Troubleshooting See Test Gun Resistance onSee Check Electrical Grounding on 16 and Test Gun ResistancePrepare the Gun for Service RepairInstall the Gun on the Manifold Remove the Gun from the ManifoldTip Guard, Air Cap, Spray Tip, or Seat Housing Replacement Tip Guard, Air Cap, and Spray Tip Replace- mentRepair Electrode Replacement Electrode ReplacementFluid Tube Replacement Fluid Filter RemovalFluid Needle Replacement Not overtightenPiston Repair Piston O-RingsAdjust the Actuator Arm Actuator Arm AdjustmentBarrel Removal Barrel RemovalBarrel Installation Barrel InstallationPower Supply Removal and Replacement Turbine Alternator Removal and Replacement Power SupplyPart No PRO Auto Xs AA Electrostatic Gun, Series a PartsRef. No Alternator Detail Description Qty Plug Spray Tip Selection Chart Fan Width at Orifice SizeAccessories Gun AccessoriesAir Line Accessories Fluid Line AccessoriesSafety Warning Signs Paint ProbeES Display Module Fiber Optic Y CablesAccessories 309298J Technical Data Category DataGraco Information Graco Standard WarrantyToll Free

244592, PRO Auto Xs AA, TI1713A, 309298J specifications

Graco Inc is a renowned brand in the field of fluid handling systems and accessories, with a reputation for delivering high-quality products that serve a variety of industries, including automotive, construction, and manufacturing. Among their extensive lineup, the Graco 309298J, TI1713A, PRO Auto Xs AA, 244592 represents a significant advancement in spray technology, notably regarded for its efficiency and versatility.

The Graco 309298J model is a part of the PRO Auto Xs series, designed specifically for high-performance spray applications. One of the standout features of this equipment is its auto-adjusting technology, which automatically adapts the spray pattern based on the surface being coated. This ensures uniform coverage and reduces the waste of material, making it an environmentally friendly option.

Equipped with an ergonomic design, the PRO Auto Xs AA enhances user comfort and reduces fatigue during prolonged use. The lightweight construction makes it easy to handle, while the balanced design allows for precise control, ensuring that even intricate spray patterns can be achieved with minimal effort.

Technologically, this spray gun incorporates advanced fluid dynamics that allow it to produce fine atomization, resulting in a superior finish. The easy-to-clean design coupled with a durable construction ensures that maintenance is straightforward, which is crucial for professionals who require reliability under demanding conditions.

Another notable characteristic is the Graco TI1713A tip, which is compatible with a variety of coatings, including paint, stains, and sealers. This versatility allows users to switch seamlessly between different materials without the need for extensive reconfiguration. The adjustability of the spray width further adds to its functionality, enabling operators to customize the application based on the job requirements.

Additionally, the 244592 model is designed with safety features, such as anti-drip mechanisms and pressure control valves, ensuring safe operation. Graco's commitment to quality is evident in the durability of its products, as they withstand the rigors of daily use while delivering consistent performance over time.

In summary, the Graco 309298J Pro Auto Xs AA, 244592 is a sophisticated spray solution that showcases the fusion of advanced technology and user-centric design, catering to professionals seeking efficiency, versatility, and reliability in their spray applications. This model stands out as an essential tool for anyone looking to enhance their workflow and achieve exceptional finish quality.
Top Page Image Contents