Graco Inc G40 Air Cap Seal Kit, Plastic Seat Repair Kit, Bleed-type Master Air Valve, Brush

Page 35

Air Cap Seal Kit 253032

Pack of five seals and five o-rings for the air cap assembly.

Plastic Seat Repair Kit 249424

Kit includes replacement plastic seat (pack of ten), and seat nut.

Accessories

Bleed-type Master Air Valve

300 psi (2.1 MPa, 21 bar) Maximum Working Pressure Relieves air trapped in the air line between the pump air inlet and this valve when closed.

Part No. Description

107141 3/4 npt(m x f) inlet and outlet

107142 1/2 npt(m x f) inlet and outlet

SST Seat Repair Kit 287962

Kit includes assembled diffuser with SST seat (15H282) for use with pigmented acid catalyzed materials.

Ultimate Gun Cleaning Kit 15C161

Kit includes brushes and tools for gun maintenance.

Carbide Seat Repair Kit 249456

Kit includes replacement carbide seat, seat gasket, and seat nut.

Tip Filter Kit 241804

Replacement filters (pack of ten) for spray tip orifice sizes 0.007, 0.009, and 0.011.

Grounding Clamp and Wire 222011

In-line Fluid Filter 210500

5000 psi (35 MPa, 350 bar) Maximum Working Pressure 100 mesh. Fits onto the gun's fluid connector. 1/4-18 npsm. Includes the parts shown below.

168517

Filter

164075

Unclogging Needle 249598

Kit includes picks for unclogging gun tip.

Brush 101892

For cleaning the gun.

Retrofit Adapter Plate 288197

The retrofit adapter plate enables the manifold to be attached to a variety of bolt patterns.

210501

205264

High Pressure Ball Valves, Fluoroelastomer Seals

5000 psi (34 MPa, 345 bar) Maximum Working Pressure Can be used as fluid drain valve.

•210657 1/2 npt(m)

•210658 3/8 npt(m)

•210659 3/8 x 1/4 npt(m)

311052E

35

Image 35

Contents Automatic G40 Air-Assisted Spray Guns Related Manuals ContentsG40 RAC Spray Gun, 288053, Series a ModelsG40 Standard Spray Gun, 288046, Series a G40 Plastic Seat Spray Gun, 288044, Series BEquipment Misuse Hazard Pressurized Equipment Hazard Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround System Install Air FittingsRetrofit Adapter Plate Mount GunReciprocating Arm Rod Mount Stationary SupportConnect Air Line Side Mounted Manifold Ports Connect Fluid LineSetup Operation Pressure Relief ProcedureAdjust Spray Pattern No air Too little air Correct amount Air Apply FluidIncorrect CorrectDaily Gun Care MaintenanceFlushing and Cleaning General System MaintenanceTurn off the solvent supply Problem Cause Solution TroubleshootingGeneral Troubleshooting Problem Cause Solution Spray Pattern Troubleshooting Items Needed for Service ServiceDisassembly TI8173b Cutaway View Part No Gun Shown Reassembly Diffuser Seat ReplacementParts AA RAC Assembly included with Model 288053 onlyPart Ref. No. No Description Qty PartsNorth America and International Manifold Description QtyManifold with Bottom Fluid Ports Part No. Description QtyPart No C343 Side Fluid Ports and Fan Adjustment ValveRING, Ptfe 311052E Typical Air Application Tip Used With Consumption AAP Series Tip and Air Cap Selection ChartsAAP Series Precision Spray Tips LTX Reverse-A-Clean RAC Spray Tips LTX Series RAC Tip Selection ChartsFor use with G40 RAC Housing WRX Wide RAC Spray Tips RAC Switch TipsFFT Fine Finish RAC Spray Tips Accessories Plastic Seat Repair Kit Ultimate Gun Cleaning Kit 15C161Grounding Clamp and Wire In-line Fluid Filter Air Cap Seal KitDimensions Mounting Hole Layout Gun with Rear Port Manifold Rear Port ManifoldModels 3/16 in. ball Cylinder Air Pressure Fluid Pressure Technical DataTriggering Speed Sound Data dBaGraco Information Graco Standard Warranty