Graco Inc TI3840a, 309856P, 2004230905 important safety instructions Fire and Explosion Hazard

Page 10

Warning

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

•Use equipment only in well ventilated area.

•Eliminate all ignition sources, such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

•Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

•Keep the work area free of debris, including solvent, rags, and gasoline.

•Ground equipment and conductive objects. See Grounding, page 12.

•Hold gun firmly to side of grounded pail when triggering into pail.

•Use only grounded hoses.

•If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

EQUIPMENT MISUSE HAZARD

Misuse can cause serious injury or death.

•For professional use only.

•Use equipment only for its intended purpose. Call your Graco distributor for information.

•Read manuals, warnings, tags, and labels before operating equipment. Follow instructions.

•Check equipment daily. Repair or replace worn or damaged parts immediately.

•Do not alter or modify equipment. Use only Graco parts and accessories.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not use hoses to pull equipment.

•Comply with all applicable safety regulations.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage.

10

309856P

Image 10

Contents Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions Standard Round Pattern Guns List of Models/Selection GuidePressure in psi MPa, bar Standard Flat Pattern Guns Direct Impingement Round Pattern Guns Flow Rate in gpm lpmDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Overall View KeyKeep a and B Components Separate Piston Safety LockIsocyanate Hazard GroundingSetup ISODisengage piston safety lock, Adjust Purge Rod 1/4 TurnAdjust Flat CeramTip Daily Shutdown Follow Pressure Relief Procedure,Shutdown Shutdown for More than a DayPressure Relief Procedure Optional Configurations Optional Fluid Manifold PositionFluid Hoses Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Air HoseMaintenance Clean Muffler Clean Outside of GunClean Air Cap Clean Fluid ManifoldClean Slip-Fit Polycarballoy Mix Module Cleaning Component a ISO PortsImpingement Port Cleanout Drill Sizes Impingement Port Drill Counterbore DrillXF1313 #81 Cleanout Drill Sizes for Round CeramTips Clean CeramTipExternal Quick Cleaning Method Round CeramTipAdjust Purge Rod, Clean Purge RodStuck Purge Rod Reassemble Front End, Adjust Purge Rod, Adjust Front Rod SealDisassemble Front End, Adjust Rear Rod Seal Troubleshooting See Clean Purge Rod,Adjust Rear Rod Seal, Gun Triggered Fluid Spraying Theory of OperationGun Detriggered Mechanical Purging Cutaway View Lubrication RepairTools Required Replace CeramTipDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Piston Safety Lock Air Valve309856P Parts Flush Manifold DetailPart No. Description Qty HandleStandard Round Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Flat Pattern GunsDirect Impingement Round Pattern Guns Direct Impingement Flat Pattern GunsFlat CeramTip Part Numbering Code CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTipsDrill Bit Kits Kit Part No Qty in Kit Drill Bit Size Illustration NominalGun Repair Kits Check Valve Filter Screen Kits 10 per kitAccessories Hose Adapter Kits Solvent Flush Pail KitPour Nozzle Kit Technical Data Category DataGraco Information Graco Standard WarrantyToll Free