Graco Inc 309856P, TI3840a, 2004230905 Personal Protective Equipment

Page 9

Warning

WARNING

PERSONAL PROTECTIVE EQUIPMENT

You must wear proper protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

•Protective eyewear

•Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

•Hearing protection.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

•Read Material Safety Data Sheet (MSDS) to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

•Do not point the gun at anyone or at any part of the body.

•Do not put your hand over the spray tip.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Do not “blow back” fluid; this is not an air spray system.

•Follow Pressure Relief Procedure, page 18, when you stop spraying and before cleaning, check- ing, or servicing equipment.

•Use lowest possible pressure when flushing, priming, or troubleshooting.

•Engage piston safety lock when not spraying.

•Tighten all fluid connections before operating the equipment.

•Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. High pres- sure hose cannot be recoupled; replace the entire hose.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.

309856P

9

Image 9

Contents Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions List of Models/Selection Guide Standard Round Pattern GunsPressure in psi MPa, bar Standard Flat Pattern Guns Flow Rate in gpm lpm Direct Impingement Round Pattern GunsDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Key Overall ViewIsocyanate Hazard Piston Safety LockKeep a and B Components Separate GroundingISO SetupDisengage piston safety lock, 1/4 Turn Adjust Purge RodAdjust Flat CeramTip Shutdown Follow Pressure Relief Procedure,Daily Shutdown Shutdown for More than a DayPressure Relief Procedure Optional Fluid Manifold Position Optional ConfigurationsOptional Hose Position Follow Pressure Relief Procedure, page 18. AlsoFluid Hoses Air HoseMaintenance Clean Air Cap Clean Outside of GunClean Muffler Clean Fluid ManifoldCleaning Component a ISO Ports Clean Slip-Fit Polycarballoy Mix ModuleImpingement Port Drill Counterbore Drill Impingement Port Cleanout Drill SizesXF1313 #81 External Quick Cleaning Method Clean CeramTipCleanout Drill Sizes for Round CeramTips Round CeramTipClean Purge Rod Adjust Purge Rod,Stuck Purge Rod Adjust Front Rod Seal Reassemble Front End, Adjust Purge Rod,Disassemble Front End, Adjust Rear Rod Seal See Clean Purge Rod, TroubleshootingAdjust Rear Rod Seal, Theory of Operation Gun Triggered Fluid SprayingGun Detriggered Mechanical Purging Cutaway View Tools Required RepairLubrication Replace CeramTipDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Air Valve Piston Safety Lock309856P Flush Manifold Detail PartsHandle Part No. Description QtySlip-Fit Polycarballoy Mix Module Part Numbering Code Slip-Fit Polycarballoy Mix Module KitsStandard Round Pattern Guns Standard Flat Pattern GunsDirect Impingement Flat Pattern Guns Direct Impingement Round Pattern GunsRound CeramTip Part Numbering Code CeramTip KitsFlat CeramTip Part Numbering Code Flat CeramTipsKit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit KitsCheck Valve Filter Screen Kits 10 per kit Gun Repair KitsAccessories Solvent Flush Pail Kit Hose Adapter KitsPour Nozzle Kit Category Data Technical DataGraco Standard Warranty Graco InformationToll Free