Graco Inc TI3840a, 309856P Slip-Fit Polycarballoy Mix Module, Follow Pressure Relief Procedure

Page 38

Repair

Slip-Fit Polycarballoy Mix Module

See page 48 for available Slip-Fit Polycarballoy Mix Module sizes.

1. Follow Pressure Relief Procedure, page 18.

2. Flush Gun, page 22.

3. Remove fluid manifold (G). Leave air connected.

G

TI3852a

4. Remove air cap (9), retainer (28), and CeramTip

(40).

28 40

9

TI3843a

5. Remove mix module nut (25), using air cap (9) backwards, or a wrench. Remove front seal (46).

9

46

25

TI3843a

6. Disengage piston safety lock, page 12. Trigger and

detrigger gun once to release mix module (39) from fluid housing (7). Remove mix module. Engage piston safety lock.

39

7

TI3845a

If mix module (39) does not protrude from fluid housing (7), slightly loosen then retighten lock ring (11), to allow gripping of edge for removal.

7. Push mix module (39) onto rod (31) as far as pos-

sible.

3931

7

TI3845a

38

309856P

Image 38
Contents Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions Pressure in psi MPa, bar List of Models/Selection GuideStandard Round Pattern Guns Standard Flat Pattern Guns Direct Impingement Round Pattern Guns Flow Rate in gpm lpmDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Overall View KeyKeep a and B Components Separate Piston Safety LockIsocyanate Hazard GroundingSetup ISODisengage piston safety lock, Adjust Purge Rod 1/4 TurnAdjust Flat CeramTip Daily Shutdown Follow Pressure Relief Procedure,Shutdown Shutdown for More than a DayPressure Relief Procedure Optional Configurations Optional Fluid Manifold PositionFluid Hoses Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Air HoseMaintenance Clean Muffler Clean Outside of GunClean Air Cap Clean Fluid ManifoldClean Slip-Fit Polycarballoy Mix Module Cleaning Component a ISO PortsImpingement Port Cleanout Drill Sizes Impingement Port Drill Counterbore DrillXF1313 #81 Cleanout Drill Sizes for Round CeramTips Clean CeramTipExternal Quick Cleaning Method Round CeramTipStuck Purge Rod Clean Purge RodAdjust Purge Rod, Disassemble Front End, Adjust Front Rod SealReassemble Front End, Adjust Purge Rod, Adjust Rear Rod Seal Troubleshooting See Clean Purge Rod,Adjust Rear Rod Seal, Gun Detriggered Mechanical Purging Theory of OperationGun Triggered Fluid Spraying Cutaway View Lubrication RepairTools Required Replace CeramTipDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Piston Safety Lock Air Valve309856P Parts Flush Manifold DetailPart No. Description Qty HandleStandard Round Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Flat Pattern GunsDirect Impingement Round Pattern Guns Direct Impingement Flat Pattern GunsFlat CeramTip Part Numbering Code CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTipsDrill Bit Kits Kit Part No Qty in Kit Drill Bit Size Illustration NominalGun Repair Kits Check Valve Filter Screen Kits 10 per kitAccessories Pour Nozzle Kit Solvent Flush Pail KitHose Adapter Kits Technical Data Category DataToll Free Graco Standard WarrantyGraco Information