I.C.T.C. Holdings Corporation B series owner manual Important Safety Precautions

Page 4

IMPORTANT SAFETY PRECAUTIONS

WARNING

NEVER PLACE FINGERS NEAR SPRAY TIP OF GUN. NEVER POINT GUN TOWARD ANY PART OF YOUR BODY, OR THAT OF ANY OTHER PERSON. MATERIAL ISSUING FROM THE SPRAY TIP IS AT HIGH PRESSURE. IF FINGERS, OR ANY PART OF THE BODY ARE PLACED NEAR THE TIP OF THE SPRAY GUN, IT IS POSSIBLE THAT THE SPRAY COULD BREAK THE SKIN AND INJECT SOME OF THE SPRAY MATERIAL. IF INJURY DOES OCCUR, SEEK THE IMMEDIATE ATTENTION OF A MEDICAL DOCTOR. BE PREPARED TO INFORM THE DOCTOR WHAT FLUID WAS INJECTED, IF THE INJURY IS OF AN INJECTION NATURE. EQUIPMENT AND CHEMICALS WHEN USED IMPROPERLY CAN BE DANGEROUS!

ýNEVER place any part of the body in front of the spray tip or aim the gun toward any part of the body.

ýNEVER point the gun toward any individual.

ýNEVER treat any injury as a simple cut. If injury does occur, seek immediate medical attention. Be prepared to inform the doctor what fluid was injected.

ýNEVER allow another person to use the sprayer unless he is thoroughly instructed on its operation and has read all safety precautions in this manual and all safety warning labels attached to unit.

ýNEVER use around children.

ýNEVER attempt to perform any maintenance or service on any part of the unit spray system without first;

1.Shutting off the unit.

2.Disconnecting the power cord from the outlet.

3.Relieving all pressure in the pump by triggering the gun.

4.Locking gun trigger in "LOCKED" position, with gun locked closed.

ýNEVER operate the sprayer without the tip guard complete and in place.

ýNEVER spray any material in the vicinity of open flame, pilot lights, electrical outlets or any other source of ignition.

ýNEVER spray volatile materials with flash points lower than 140 F (60 C).

ýNEVER attempt to stop any leakage in the paint line or at any fitting with your hand or any part of your body. Immediately shut off the unit should leakage occur.

ýNEVER wash an electric motor, nor operate it in the rain or in wet or damp areas, to protect yourself from electric shock.

ýNEVER allow paint hose to become kinked, or to vibrate against rough or sharp surfaces.

ýNEVER operate the unit at pressures higher than the pressure rating of the lowest rated component in the system, or at pressure higher than factory preset.

ýNEVER spray in an enclosed area. The spraying area must be well ventilated to safely remove chemical vapors.

ýNEVER operate the unit with worn or damaged accessories, or with accessories other than those supplied by H.E.R.O. Industries, unless the accessories have been first specifically approved in writing by H.E.R.O. Industries Ltd.

ýNEVER allow the unit to be serviced or repaired anywhere other than an authorized H.E.R.O. Service Center, or with other than genuine H.E.R.O. parts or components.

ýNEVER leave unit unattended without first shutting off, triggering the gun to relieve all pump pressure, and setting the trigger lock on gun in "LOCKED" position, with gun locked closed.

H.E.R.O. INDUSTRIES LTD.

3

1100MD OWNERS MANUAL - “B” VERSION

Image 4
Contents NEW For Hydrapulse B Version Starting with serial R.O. Warranty Table of Contents Important Safety Precautions Always AlwaysR.O. Airless Spray Painting Series Hydrapulse Intake AssemblyOperating Instructions Setting UP to Spray Flushing the Unit AT Shutdown Or Color Change Special Storage InstructionsSpecial Notes General Maintenance Instructions Airless Spray Painting Suggestions and Technique For Excellent RESULTS, Read and Practice These TechniquesPoor Good Tailing Good Pattern Fog, Overspray Spray TIP Selection TIP Size For ApplicationTroubleshooting Hydraulic Intake Valve REF# 59 Pressure Test Hydrapulse Membrane Test Situation Sprayer does not Prime with Paint Puddle of OIL Appearing Under Sprayer During Operation Spray Pattern is Spotty or Uneven Hydrapulse Membrane Replacement REF# 46 KITReplacement of Intake Seat REF # Outgo Valve REF# Tools Required -1 wrenchPiston Repairs REF#Page Pressure Control Valve Accessories Parts List Parts ListIntake Parts Outgo Parts 45A TANK, Complete. Includes Ref# Drive Parts 116 PW-4080 Foot PAD, Includes Ref# 1100MD Schematic Partsschematics Authorized Sales and Service Centers U.S.A Authorized Sales and Service CENTERS- U.S.A Southern CaliforniaNEW York Rhode Island R.O. Industries 2719 Lake City WAY BURNABY, B.C Canada