I.C.T.C. Holdings Corporation B series R.O. Airless Spray Painting, Operating Instructions

Page 6

H.E.R.O. AIRLESS SPRAY PAINTING

Welcome to the world of H.E.R.O. airless paint spraying. We are sure you will enjoy owning and operating your new H.E.R.O. model 1100MD. With H.E.R.O. airless spray equipment you will avoid the inconvenience and mess of overspray. You are spraying paint, not air, and the paint is driven to the painting surface in a clean, fan shaped spray which penetrates all cracks and corners. To attain these results, you must adjust the pressure as low as possible. We recommend that you become familiar with your H.E.R.O. unit. Discuss with your dealer the useful accessory items he has to offer - various types of tips, extension poles for hard to reach areas, extra hose, etc. Use of accessory items is often the difference between a good job and an excellent one!

NEW 1997

“B” SERIES

HYDRAPULSE

INTAKE

ASSEMBLY

BEGINNING WITH SERIAL NUMBER 190031

OPERATING INSTRUCTIONS

WARNING

Do not attempt to operate this machine until you have read and understood all safety precautions and operating instructions. Equipment and chemicals when used improperly can be dangerous.

Your H.E.R.O. airless sprayer has been fully factory tested prior to shipment.

BEFORE STARTING YOUR H.E.R.O. PUMP....

CHECK to ensure that the shipping seal has been removed from under the cap on the hydraulic tank. Hydraulic tank should be at least 3/4 full of H.E.R.O. LVO hydraulic fluid.

CHECK all fittings and connections in the pump system, hose, and gun to ensure that they are tight. CHECK to ensure that there is a spray tip in the gun, and that the tip is the correct size for the coating you are to spray. ( There are various tips available, for each type of coating or configuration. See " Airless Spray Tip " on page 11 , for proper tip selection.

CHECK to ensure that you have H.E.R.O. strainer bags, H.E.R.O. Wonder Wash, appropriate thinner for the paint, a waste container, and any other accessories you may require for the job.

CHECK to ensure that you have adequate extension cord size and length if the machine cannot be situated immediately next to an electric outlet. Distances up to 50 feet require #12/3 wire grounded cord, up to 100 feet require #10/3 wire grounded cord. DO NOT exceed 100 feet of extension cord. If distance is greater, obtain and install extra length of H.E.R.O. airless spray hose.

READ THIS MANUAL THOROUGHLY.

H.E.R.O. INDUSTRIES LTD.

5

1100MD OWNERS MANUAL - “B” VERSION

Image 6
Contents NEW For Hydrapulse B Version Starting with serial R.O. Warranty Table of Contents Important Safety Precautions Always AlwaysSeries Hydrapulse Intake Assembly R.O. Airless Spray PaintingOperating Instructions Setting UP to Spray Flushing the Unit AT Shutdown Or Color Change Special Storage InstructionsSpecial Notes General Maintenance Instructions Airless Spray Painting Suggestions and Technique For Excellent RESULTS, Read and Practice These TechniquesPoor Good Tailing Good Pattern Fog, Overspray Spray TIP Selection TIP Size For ApplicationTroubleshooting Hydraulic Intake Valve REF# 59 Pressure Test Hydrapulse Membrane Test Situation Sprayer does not Prime with Paint Puddle of OIL Appearing Under Sprayer During Operation Spray Pattern is Spotty or Uneven Hydrapulse Membrane Replacement REF# 46 KITReplacement of Intake Seat REF # Outgo Valve REF# Tools Required -1 wrenchPiston Repairs REF#Page Pressure Control Valve Accessories Parts List Parts ListIntake Parts Outgo Parts 45A TANK, Complete. Includes Ref# Drive Parts 116 PW-4080 Foot PAD, Includes Ref# 1100MD Schematic Partsschematics Authorized Sales and Service Centers U.S.A Authorized Sales and Service CENTERS- U.S.A Southern CaliforniaNEW York Rhode Island R.O. Industries 2719 Lake City WAY BURNABY, B.C Canada