3M 3M owner manual To reduce the risks associated with all residual hazards

Page 3

WARNING

To reduce the risks associated with all residual hazards:

Read, understand, follow and retain for future reference all safety statements in each applicable equipment owner’s manual and refer to the applicable Material Safety Data Sheet and material container label for each material to be sprayed before using your 3M equipment.

This equipment is to be used only by professionals familiar with the possible applicable safety hazards.

Do not use this product around unsupervised children.

Never modify any part of this product.

Always comply with local, state, and national codes governing ventilation, fire protection, operation, maintenance, housekeeping and disposal plus all safety statements in applicable owner manuals, MSDS and material container labels.

To reduce the risks associated with chemical exposure:

Check spray equipment for damage and proper function. Repair or replace worn, damaged or malfunctioning components.

Always wear appropriate, approved personal protective equipment for eye, skin, respiratory and hearing protection per the applicable MSDS and material container labels at all times when spraying.

To reduce the risks associated with fire and explosion:

Must maintain adequate ventilation per applicable MSDS and material container labels for each material being sprayed in the work area.

All ignition sources such as smoking must be kept out of the spray area.

Always maintain a readily available, approved fire extinguisher or other approved fire fighting equipment in the spray area.

Always locate air compressor as far away from spray area as the air supply hoses allow.

Never use solvents containing Methylene Chloride and Trichloromethane for any reason to avoid a possible violent, explosive chemical reaction when exposed to aluminum or zinc (refer to the manufacturer's MSDS or contact material supplier if there is any doubt to confirm compatibility).

CAUTION

To reduce the risks associated with lifting and handling:

Always follow proper lifting and handling practices when moving system components.

To reduce the risks associated with tripping, falling and tipping:

Route air hoses and any extension cords away from traffic areas, sharp edges, moving parts and hot surfaces. Do not pull on air hoses to move the compressor.

To reduce the risks associated with hazardous air pressure:

Maintain spray equipment per 3M care and cleaning instructions in the applicable owner’s manual.

Ensure air input pressure and all applicator system regulators are properly adjusted per materials recommendations prior to each use.

Always follow required air pressure relief procedures for relieving air pressure from the unit.

To reduce the risks associated with compression spring release:

• Maintain a firm grip on fluid adjustment knob when removing.

To reduce the risks associated with environmental contamination:

Spray materials, solvents, other cleaning materials and electronic components must be disposed of per federal, state and local regulations.

3

3

4

Image 3
Contents 3M Series Series 05 de 3M Explanation of Product Safety Label Symbols Table of Contents3M Series 05 Spray Gun Safety Statements Explanation of Signal Word ConsequencesTo reduce the risks associated with lifting and handling To reduce the risks associated with all residual hazardsTo reduce the risks associated with chemical exposure To reduce the risks associated with fire and explosionSpray Gun Overview EC Declaration of ConformityGeneral Set Up and Spray Gun Use ContentsSpray Technique Adjusting the Fan Pattern SizeFan Adjustment Knob General System MaintenanceRemove the fluid nozzle with the wrench Clean the air line filters dailyCleaning Process Relieve the pressure3M Series 05-100 Spray Gun Parts Identification 3M Series 05-100 Spray Gun Parts IdentificationDescription 3M Series 05-300 Spray Gun Parts Identification 3M Series 05-300 Spray Gun Parts Identification3M Series 05-300 Spray Gun Troubleshooting3M Needle/Nozzle/Air Cap Selection Guide 3M Series 05-100 Spray GunTabla de Contenidos Spray Equipment Warranty and Limited RemedyAtención Lea la documentación adjunta Uso PrevistoDeclaración de Conformidad de la Comunidad Europea Pistola aplicadora en spray Imprimador Serie 05-100 de 3M Generalidades del Pistola aplicadora en sprayContenido DesempaqueInstalación y Uso General del Pistola aplicadora en spray Técnica de PulverizaciónAjuste de Flujo de Líquidos Cuidado y Limpieza del Pistola aplicadora en spray Mantenimiento General del SistemaProceso de Limpieza Page Kit de Tapa del Aire y Aguja Artículo DescripciónKit de Aguja 97-210/0.8 97-210/1.0 97-210/1.2 Guía de Selección de la Tapa del Aire/Boquilla/Punta de 3MKit de la Aguja Tamaño DescripciónProblema Causa Remedio Solución de problemas34-8703-6855-1 Printed Colors Front Printed Colors Back Match Colors Creator deZinniaStructure # SS-18217