OPERATING: POWER UNIT
TRIGGER SWITCH & FORWARD/REVERSE SLIDER
The forward/reverse slider (7) is used to control the direction the chuck (12) spins - foward to drive screws, reverse to remove screws. It is located above the variable speed trigger (8). To reverse the motor, release the trigger FIRST, then push the slider to the right hand side of the tool when viewing from the rear. After any reversing operations, return lever to the forward position. Never change the direction of rotation while the motor is running.
7KH3RZHU8QLWLVWXUQHG21 QG2)) \SXOOLQJ QGUHOH VLQJWKHWULJJHU7KHI UWKHUWKH
trigger is depressed, the higher the speed of the Power Unit.
$IRUZ UGUHYHUVHFRQWUROVOLGHUGHWHUPLQHVWKHGLUHFWLRQRIWKHWRRO
7RVHOHFWIRUZ UGURW WLRQUHOH VHWKHWULJJHUVZLWFK QGGHSUHVVWKHIRUZ UGUHYHUVHFRQWURO
button to the left.
7RVHOHFWUHYHUVHGHSUHVVWKHIRUZ UGUHYHUVHFRQWURO XWWRQWRWKHULJKW
NOTE: When changing the position of the control button, be sure the trigger is released.
INSTALLING AND REMOVING ATTACHMENTS
G
WARNING: Shock hazard. Under no circumstances should this product be used near water.
WARNING: Burn hazard. Moving parts within the Power Unit become hot during use. Avoid contact with moving parts within Power Unit when removing and installing accessories.
WARNING: Before assembly, lock the Power Unit by 
setting the forward/reverse slider (7) to the center position and remove the battery from the Power Unit. Remove any accessory from the attachment before removing or installing the attachment.
WARNING: To reduce the risk of injury, do not place fingers or other objects inside the Power Unit, other than the attachments designed to work with the Power Unit.
Lock the Power Unit by setting the forward/reverse slider (7) to the center position.
To remove an attachment, depress the release button (9) and take the attachment off the tool.
7RÀW Q WW FKPHQWOLQHLWXSZLWKWKHWRRO VVKRZQ QGSXVKLWRQWRWKH3RZHU8QLWXQWLOLWVQ SV into place and an audible click is heard.
(QVXUH WW FKPHQWLVVHFXUHO\ WW FKHG \JHQWO\SXOOLQJLW Z \IURPWKH3RZHU8QLW NOTE: Only use attachments that are specifically designed for and compatible with the Power Unit.
NOTE: Refer to individual attachment instruction manuals for specific safety warnings and operating instructions before operating attachments with the Power Unit.
OPERATING: DRILL/SCREWDRIVER ATTACHMENT
SAFETY WARNINGS AND INSTRUCTIONS: DRILLS
1.Hold drill firmly with one hand on the grip and the other hand on the bottom of the battery pack unless an auxillary handle has been supplied with the tool. Use auxillary handle if supplied with the tool.
2.When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before
WARNING: Let the tool work at its own pace. Do not overload.
WARNING: Before drilling into walls, floors or ceilings, check for the location of wiring and pipes.
FITTING AND REMOVING A DRILL BIT OR SCREWDRIVER BIT
The drill/screwdriver attachment (11) is fitted with a keyless chuck (12) to allow for an easy exchange of bits.
/RFNWKHWRRO \VHWWLQJWKHIRUZ UGUHYHUVHVOLGHU WRWKHFHQWHUSRVLWLRQ
2SHQWKHFKXFN \WXUQLQJWKHIURQWS UWFORFNZLVHZLWKRQHK QGZKLOHKROGLQJWKHUH US UW
with the other.
10