'2127&/,&.7+(75,**(52)$67$//(''5,//2))$1'21,1$1$77(03772
START IT. DAMAGE TO THE DRILL CAN RESULT.
0LQLPL]HVW OOLQJRQ UH NWKURXJK \UHGXFLQJSUHVVXUH QGVORZO\GULOOLQJWKURXJKWKHO VWS UWRIWKHKROH .HHSWKHPRWRUUXQQLQJZKLOHSXOOLQJWKH LWRXWRI GULOOHGKROH7KLVZLOOKHOSUHGXFHM PPLQJ Make sure switch turns drill on and off.
DRILLING IN WOOD
Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.
DRILLING IN METAL
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
TROUBLESHOOTING
| Problem | UW | Possible Cause |
| Possible Solution | ||
8QLWZLOOQRWVW | % WWHU\S FNQRWLQVW OOHGSURSHUO\ | &KHFN | WWHU\S FNLQVW OO WLRQ | ||||
% WWHU\S FNQRWFK UJHG | &KHFN | WWHU\S FNFK UJLQJ | |||||
$WW FKPHQWLVQRWVHFXUHG | requirements. | ||||||
0 NHFHUW LQWKH WW FKPHQWLVIXOO\ | |||||||
% | WWHU\S FNZLOOQRWFK |
|
| pushed into the Power Unit. | |||
UJH % WWHU\S FNQRWLQVHUWHGLQWRFK UJHU ,QVHUW | WWHU\S FNLQWRFK UJHUXQWLO | ||||||
&K UJHUQRWSOXJJHGLQ | LED illuminates. | ||||||
3OXJFK UJHULQWR ZRUNLQJRXWOHW | |||||||
|
|
|
|
|
| Refer to “Important Charging Notes” | |
6XUURXQGLQJ LUWHPSHU WXUH | for more details. | ||||||
0RYHFK UJHU QG WWHU\S FNWR | |||||||
|
|
|
| too hot or too cold. |
| surrounding air temperature of above | |
|
|
|
|
|
| 40 degrees F (4,5°C) or below 105 | |
8QLWVKXWVRII | UXSWO\ | % WWHU\S FNK VUH FKHGLWV | degrees F (+40,5°C). | ||||
$OORZ | WWHU\S FNWRFRROGRZQ | ||||||
|
| maximum thermal limit. |
| 3O FHRQFK UJHU QG | |||
|
| 2XWRIFK UJH To |
| ||||
|
|
|
| maximize the life of the |
| allow to charge. | |
battery pack it is designed to shutoff abruptly when the charge is depleted.)
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at 1
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.
ACCESSORIES
WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
12