,QVHUWWKH LWVK IWLQWRWKHFKXFN
)LUPO\WLJKWHQWKHFKXFN \WXUQLQJWKHIURQWS UWFRXQWHUFORFNZLVH
7RUHPRYHWKHVFUHZGULYHU LWIURPWKHKROGHUOLIWWKH LWIURPWKHUHFHVV 7RVWRUHWKHVFUHZGULYHU LWILUPO\SXVKLWLQWRWKHKROGHU
SCREW DRIVING
$OZ \VXVHWKHFRUUHFWW\SH QGVL]HRIVFUHZGULYHU LW
,IVFUHZV UHGLIILFXOWWRWLJKWHQWU\ SSO\LQJ VP OO PRXQWRIZ VKLQJOLTXLGRUVR S V OX ULF QW $OZ \VKROGWKHWRRO QGVFUHZGULYHU LWLQ VWU LJKWOLQHZLWKWKHVFUHZ
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.
KEYLESS CHUCK FIGURE H
WARNING: To reduce the risk of injury, turn off and remove battery from the tool before making any adjustments or removing or installing attachments or accessories.
WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.
To insert a drill bit or other accessory:
1.Grasp the rear half of the chuck (12) with one hand and use your other hand to rotate the front half in the counterclockwise direction, as viewed from the chuck end.
H |
12 |
2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end.
TORQUE CONTROL FIGURE I | I |
| ||
This tool is fitted with a torque adjustment collar (13) to select the | 13 | |||
operating mode and to set the torque for tightening screws. Large |
| |||
|
| |||
screws and hard workpiece materials require a higher torque |
|
| ||
setting than small screws and soft workpiece materials. |
|
| ||
| )RUGULOOLQJLQZRRGPHW O QGSO VWLFVVHWWKHFROO UWRWKH |
|
| |
| drilling position symbol |
|
| |
)RUVFUHZGULYLQJVHWWKHFROO UWRWKHGHVLUHGVHWWLQJ,I\RXGR |
|
| ||
| not yet know the appropriate setting, proceed as follows: |
|
| |
| | 6HWWKHFROO UWRWKHORZHVWWRUTXHVHWWLQJ |
|
|
| 7LJKWHQWKHILUVWVFUHZ |
|
| |
| | ,IWKHFOXWFKU WFKHWV HIRUHWKHGHVLUHGUHVXOWLV FKLHYHGLQFUH VHWKHFROO UVHWWLQJ | ||
and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.
ONBIT STORAGE
A bit storage slot (10) is
DRILLING
8VHVK USGULOO LWVRQO\
6XSSRUW QGVHFXUHZRUNSURSHUO\ VLQVWUXFWHGLQWKH6 IHW\,QVWUXFWLRQV
8VH SSURSUL WH QGUHTXLUHGV IHW\HTXLSPHQW VLQVWUXFWHGLQWKH6 IHW\,QVWUXFWLRQV 6HFXUH QGP LQW LQZRUN UH VLQVWUXFWHGLQWKH6 IHW\,QVWUXFWLRQV
5XQWKHGULOOYHU\VORZO\XVLQJOLJKWSUHVVXUHXQWLOWKHKROHLVVW UWHGHQRXJKWRNHHSWKHGULOO bit from slipping out of it.
$SSO\SUHVVXUHLQ VWU LJKWOLQHZLWKWKH LW8VHHQRXJKSUHVVXUHWRNHHSWKH LW LWLQJ XWQRW so much as to stall the motor or deflect the bit.
Hold the drill rmly with two hands to control its twisting action.
11