Ryobi P236A INSTALLING/REMOVING Battery Pack, INSTALLING/REMOVING Bits, See Figures 4 5

Page 6

OPERATION

NOTICE:

To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation.

WARNING:

Battery tools are always in operating condition. Lock the switch when not in use or carrying at your side, when installing or removing the battery pack, and when installing or removing bits.

INSTALLING/REMOVING BATTERY PACK

See Figure 2, page 9.

Lock the switch trigger.

Insert the battery pack into the product as shown.

Make sure the latches on each side of the battery pack snap in place and that battery pack is secured in the product before beginning operation.

Depress the latches to remove the battery pack.

INSTALLING/REMOVING BITS

See Figure 3, page 9.

The AUTO-LOAD CHUCK provides fast, easy one-handed bit loading and ejecting.

The coupler has been designed to accept 1/4 in. hex bits.

To install:

Lock the switch trigger.

Remove the battery pack.

Push the bit into the coupler until it clicks into place.

Pull on the bit to make sure it is secured in the coupler. There may be some play in the installed bit; this is normal. NOTE: Use only impact quality bits with a locking groove.

WARNING:

Make sure the bit is secured in the coupler before using the impact driver. Failure to do so could cause serious personal injury.

To remove:

Lock the switch trigger.

Remove the battery pack.

With the nose of the tool pointed away from you, pull the coupler away from the driver.

The bit will eject from the coupler.

DRIVING OR REMOVING SCREWS

See Figures 4 - 5, page 9.

WARNING:

Do not drive a screw where there is likely to be hidden wiring behind the surface. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. If you must drive a screw where hidden wire could be present, always hold tool by insulated gripping surfaces (handle) when performing the operation to prevent a shock to the operator.

NOTICE:

The impact driver is not designed to be used as a drill.

Place the direction of rotation selector in the correct position for the operation.

Hold the impact driver with one hand.

Place the bit on the screw head and slowly depress the switch trigger. Start the bit slowly for more control.

NOTE: The TRI-BEAM LED will illuminate as the trigger is depressed.

As the screw is driven, impacting will begin.

This product has a Three-year Limited Warranty.

For Warranty details go to www.ryobitools.com

NOTE: MAINTENANCE INFORMATION BEGINS ON PAGE 7 AFTER FRENCH AND SPANISH

LANGUAGE SECTIONS. FIGURES (ILLUSTRATIONS) START ON PAGE 9.

6 — English

Image 6
Contents Table of Contents Table DES Matières Índice DE Contenido OPERATOR’S ManualElectrical Safety General Power Tool Safety WarningsWork Area Safety Personal SafetyImpact Driver Safety Warnings Battery Tool USE and CareService Symbols Symbol Signal MeaningName DESIGNATION/EXPLANATION Features AssemblyOperation Driving or Removing Screws INSTALLING/REMOVING Battery PackINSTALLING/REMOVING Bits Language SECTIONS. Figures Illustrations Start onRègles DE Sécurité Relatives AUX Outils Électriques AvertissementAvertissements DE Sécurité Relatifs CLÉ À Chocs Utilisation ET Entretien DE LA PileDépannage AVERTISSEMENT  SymbolesSymbole Signal Signification NOM Désignation / ExplicationCaractéristiques AssemblageUtilisation AVERTISSEMENT  INSTALLATION/RETRAIT DU BLOC-PILESINSTALLATION/RETRAIT DES Embouts Vissage ET DévissageSeguridad Eléctrica AdvertenciaSeguridad EN EL Área DE Trabajo Seguridad PersonalEmpleo Y Cuidado DE LA Herramienta DE Baterías ServicioAdvertencia SímbolosPeligro PrecauciónCaracterísticas ArmadoFuncionamiento Enroscado Y Desenroscado DE Tornillos INSTALACIÓN/DESMONTAR DEL Paquete DE BateríasInstalación / Desmontar DE LAS Brocas Maintenance EntretienMantenimiento California Proposition Proposition 65 DE L’ÉTAT DE Californie AvertissementCalifornia Propuesta DE LEY NÚM Advertencia P236A OPERATOR’S MANUAL/IMPACT Driver ONE World TECHNOLOGIES, INC