Ryobi Drill Press manual Fuel Handling, Fuelmix, Fuelling

Page 14

FUEL HANDLING

Fuelmix

IMPORTANT! The power cutter is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!Always provide for good ventilation when handling fuel.

Petrol

Fuelling

 

WARNING!The following precautions reduce

 

! the risk of fire:

Do not smoke or place any sources of heat in the

 

vicinity of the fuel.

Never refuel when the engine is running.

Open the fuel cap slowly when fuelling so that any over

 

pressure is released slowly.

Tighten the fuel cap carefully after refuelling.

Always move the machine from the fuelling place

 

before starting.

Use good quality unleaded or leaded petrol.

The lowest octane recommended is 90.

If you run the engine on a lower octane grade than 90 so-called, knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.

Two-stroke oil

For the best results use HUSQVARNA two-stroke oil, which is especially developed for power cutters. Mixing ratio 1:50 (2%).

If HUSQVARNA two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines.

Contact your dealer when selecting an oil. Mixing ratio 1:33 (3%)-1:25 (4%).

Never use two-stroke oil intended for water cooled outboard engines, so-called, outboard oil.

Never use oil intended for four-stroke engines.

Gasolin

 

Oil • Öl

 

Benzin

 

Huile • Aceite

 

Essence

 

Lit.

 

Gasolina

 

 

2%(1:50) 3%(1:33) 4%(1:25)

Lit.

5

0,10

0,15

0,20

10

0,20

0,30

0,40

15

0,30

0,45

0,60

20

0,40

0,60

0,80

US

 

US

 

gallon

 

fl. oz.

 

 

2%(1:50) 3%(1:33) 4%(1:25)

1

2 1/2

3 3/4

5 1/8

2 1/2

6 1/2

9 3/4

12 7/8

5

12 7/8

19 1/4

25 3/4

Keep the handle dry, clean and free from oil and fuel.

Clean around the fuel cap. Clean the fuel tank regularly. The fuel filter should be changed at least once per year Contamination in the tank can disrupt operations. Ensure that the fuel is well mixed by shaking the container before filling the tank.

Always exercise care when filling the fuel. Move the power cutter at least three metres from the filling area before starting. Make sure the fuel cap is tightened.

Mixing

Always mix the petrol and oil in a clean container intended for fuel.

Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

Mix (shake) the fuel mixture thoroughly before filling the saw’s fuel tank.

Do not mix more than max. one month’s supply of fuel.

If the power cutter is not used for some time the fuel tank should be emptied and cleaned.

Min 3 m

(10ft)

14 – English

Image 14
Contents 371K 375K Symbols in the Operators Manual Symbol ExplanationSymbols on the power cutter Contents Anti-vibration system Safety InstructionsStop switch Blade guard for the cutting blade MufflerThrottle lock General Safety Instructions Transport and storageCutting Fuel safetyBasic safety precautions Filling/Fuel mixture/StorageKickback Water coolingCare and storage GeneralSpecial blades Abrasive discsHigh speed portable tools Diamond blades for dry cutting Using diamond bladesDiamond blades What is WHAT? What is what on a power cutter?Checking the drive shaft and flanges AssemblyFitting the cutting head Fitting the cutting blade Blade guardFuelling Fuel HandlingFuelmix Start and Stop Start and stopChanging the drive belt MaintenanceAdjusting the drive belt Belt pulley and clutch Carburettor Fuel filter Air filterTensioning the recoil spring StarterReplacing a broken or worn starter cord Changing the broken recoil springMuffler Spark plugCooling system Monthly maintenance Daily maintenanceWeekly maintenance Cutting equipment Technical Data371K 375K EU declaration of conformity Only applies to Europe ´z+H2¶6`¨ 2003W14 114 01Also See