Ryobi SA720, SA60 manual Important Safety Instructions for Charger

Page 5

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

WARNING:

Read and understand all instructions. Failure to follow all instructions listed below, may result in elec- tric shock, fire and/or serious personal injury.

Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury.

Save these instructions. This manual contains impor- tant safety and operating instructions for charger.

Before using battery charger, read all instructions

and cautionary markings in this manual, on battery charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

CAUTION: To reduce risk of injury, charge only nickel- cadmium type rechargeable batteries. Other types of

batteries may burst causing personal injury and dam- age. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not expose charger to wet or damp conditions.

Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of damage to charger body and cord,

pull by charger plug rather than cord when discon- necting charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk of serious personal injury.

Do not abuse cord. Never carry tool by cord or yank

it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. Following this rule will reduce the risk of electric shock or fire.

An extension cord should not be used unless abso- lutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25'

50'

100'

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug.

If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incor-

rect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If

you loan someone this tool, loan them these instruc- tions also. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

WARNING:

Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well venti- lated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

Page 5

Image 5
Contents Model SA60 Model SA720 Save this Manual for Future ReferenceIntroduction Table of ContentsModel Battery Pack Charger General Safety RulesService Specific Safety RulesImportant Safety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsUnpacking SpecificationsApplications InstructionsFeatures Model SA60 Level Torque Adjustment Ring BITRight AdjustmentsReversible Removing Bits Installing BitsSee Figures 3 WrongTo Adjust Torque Adjustable Torque ClutchTo Decrease Torque Screwdriver BitsBattery Chargerpack Input Jack Indicator Light LED Charger Indicator Light LED Input Jack PlugOperation Charging Your DRILL-DRIVERTo Remove Battery Pack Model SA720 To Install Battery Pack Model SA720Battery Pack Port Latches Depress Latches To Release Important Information for RECHARG- ING HOT BatteriesDrilling SwitchLevel Level DrillingGeneral MaintenanceChuck Removal MalletBatteries Battery Pack Removal and PREPARA- Tion for RecyclingTo Retighten a Loose Chuck Drill Handle Remove Cover Battery Cover Battery REMOVAL, Preparation for Recycling Model SA60Drill Handle Battery Lead Leadbattery Terminal Batteries See Figures 17Service Model NO. and Serial no