Ryobi SAW BT3100 To Install Miter Table and Fence, Rear Rail END Plug Holder NUT Miter, Handwheel

Page 17

ASSEMBLY

■Check to make sure the rail clamps will securely clamp the rail before sliding the entire assembly into position. If not, tighten the square rail holder nut one-fourth (1/4) turn and recheck.

■Slide the rail into position over both clamps and secure.

■Mount the rear rail, following the same clamping procedure as shown for the front rail. Orient the rear rail as shown in Figure 12.

TO INSTALL MITER TABLE AND FENCE

See Figures13 and 14.

■Install the sliding miter table assembly over the front and rear rails. See Figure 13. Check that it slides easily on the rails. Push both front miter locking clamps down evenly on each side to secure. Repeat for both rear miter locking clamps.

Note: DO NOT force miter locking clamps fully down. Tighten only to flat "seated" position.

■To install the miter fence holder to the miter fence, loosen the attachment bolt by turning the adjusting clamp (the knob on top) counterclockwise. Make sure the adjusting clamp is loose enough so the bolt has enough clearance to slide in the table slot. Slide the tabs into the grooves in the miter fence. See Figure 14.

■Mount the miter fence to the miter table by installing the locator pin (below the miter fence) into hole “A” or “B”. (Hole "A" is closest to the blade.) At the same time, place the attachment bolt in the slot. Secure the adjusting clamp, but do not tighten.

■Adjust the miter indicator to the scale.

■Securely tighten the adjusting clamp.

END PLUG

FRONT RAIL

REAR RAIL

END PLUG

RAIL

HOLDER NUT

Fig. 12

MITER

TABLE BASE

REAR RAIL

Fig. 13

ADJUSTINGATTACHMENT

CLAMPBOLT

MITER

FENCE HOLDER

MITER FENCE

SCALE

FRONT
RAIL CLAMP
HANDWHEEL	BLADE
	BLADE
BEVEL	ADJUSTING	MITER
BEVEL	HANDLE	MITER
LOCKING LEVER		INDICATOR

LOCATOR

PIN HOLE "A"

Fig. 11	HOLE "B"
	HOLE "B"
	QUICK	TABLE
	QUICK	SLOT
	STOP	Fig. 14
Page 17

Image 17

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol Meaning Safety Alert SymbolRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureNo Hands Symbol Safety and International SymbolsExtension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingIn. NUT Driver Socket WrenchKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standGetting to Know Your SAW FeaturesSliding ScaleOperating Components Power SwitchBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth LASER-CUT Body Expansion Slots Blade RotationAssembling LEG Stand AssemblyMounting the LEG Stand on the Table SAW Base To Install Front and Back RailsAssembling Storage Brackets Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole BREMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear RailTo Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard To Remove the Blade Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting Plate HEX Nuts ShimsTo SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle To Lock Miter Table Adjustingmiter Clampfence Quick StopTo Make a Straight Cross CUT Miter Slide Lock Slots for Locking Miter TableTo Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel RIP CUT To Make a Bevel Cross CUTTo Make a Large Panel CUT Accessory Miter Locking Clamps Rail ClampTo Make a Compound Miter CUT Clamp Push Block Bevel To Make NON-THROUGH CutsFeatherboard To Make Dado Cuts General Maintenance MaintenanceBackup Washer LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt LockTo Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of BaseProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage Refer to Figure Ryobi 10 in mm Table SAW Model NO. BT3100See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100