Ryobi SAW BT3100 manual Ryobi Authorized Service, Center

Page 41

TROUBLE SHOOTING

PROBLEM	CAUSE	SOLUTION
Saw does not make accurate 90 or	Positive stops inside cabinet need	Adjust positive stops.
45 degree cuts.	adjusting (Bevel Cuts).
	Miter gage is misaligned	Adjust the miter gage.
	(Miter Cuts).

Blade adjusting handle is hard to turn.

Gears or Screw Post inside cabinet Clean the gears or screw post. are clogged with sawdust.

Saw does not start.		Motor cord or wall cord is not	Plug in motor cord or wall cord.
		plugged in.
		Circuit fuse is blown.	Replace circuit fuse.
		Circuit breaker is tripped.	Reset circuit breaker.
		Cord or switch is damaged.	Have the cord or switch replaced at
			a RYOBI AUTHORIZED SERVICE
			CENTER.

Blade makes poor cuts		Blade is dull or dirty.	Clean, sharpen or replace blade.
		Blade is wrong type for cut being
		made.	Replace with correct type.
		Blade is mounted backwards.	Remount blade.

Blade does not lower when turning blade adjusting handle.

Back side of riving knife has come in contact with saw table.

Locking lever is not at full left position.

Realign and adjust the riving knife.

Move locking lever to left.

Motor labors in rip cut.

Blade not proper for rip cut.

Change blade; rip blade typically has fewer teeth such as Ryobi 4650324, 24 tooth, carbide rip blade.

Page 41

Image 41

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol Meaning Safety Alert SymbolRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureNo Hands Symbol Safety and International SymbolsExtension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingIn. NUT Driver Socket WrenchKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standGetting to Know Your SAW FeaturesSliding ScaleOperating Components Power SwitchBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth LASER-CUT Body Expansion Slots Blade RotationAssembling LEG Stand AssemblyMounting the LEG Stand on the Table SAW Base To Install Front and Back RailsAssembling Storage Brackets Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole BREMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear RailTo Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard To Remove the Blade Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting Plate HEX Nuts ShimsTo SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle To Lock Miter Table Adjustingmiter Clampfence Quick StopTo Make a Straight Cross CUT Miter Slide Lock Slots for Locking Miter TableTo Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel RIP CUT To Make a Bevel Cross CUTTo Make a Large Panel CUT Accessory Miter Locking Clamps Rail ClampTo Make a Compound Miter CUT Clamp Push Block Bevel To Make NON-THROUGH CutsFeatherboard To Make Dado Cuts General Maintenance MaintenanceBackup Washer LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt LockTo Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of BaseProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage Refer to Figure Ryobi 10 in mm Table SAW Model NO. BT3100See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100