Ryobi SAW BT3100 manual Ryobi 10 in mm Table SAW Model NO. BT3100

Page 50

Page 50

RYOBI 10 in. (254 mm) TABLE SAW – MODEL NO. BT3100

The model number will be found on the data plate attached to the right side panel of the cabinet, next to the saw’s on board receptacle. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.

6
			11
	12		13
	12		9
5	8		12	6
	8
		2
9	3	2	12
			12
			8

10 1

FIG. 64

Image 50

Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Safety Alert Symbol Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols No Hands SymbolElectrical Connection ElectricalExtension Cords Grounding InstructionsGlossary of Terms In. NUT Driver UnpackingTools Needed Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JSliding FeaturesGetting to Know Your SAW ScalePower Switch Operating ComponentsPrecision Ground MICRO-GRAIN Carbide Teeth Speed and WiringBlades LASER-CUT Body Expansion Slots Blade RotationAssembly Assembling LEG StandMounting the LEG Stand on the Table SAW Base To Install Front and Back RailsAssembling Storage Brackets Handwheel To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter Hole BLever To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate FIT LIP of Table Into Rear RailSmall HEX Wrench To Check SAW Blade InstallationTo Install Blade Guard Assembly Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard To Remove the Blade Inch Blade Guard Riving KnifeRiving Knife Blade Riving Knife Mounting Plate HEX Nuts ShimsTo SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopTo Lock Miter Table Miter Slide Lock Slots for Locking Miter TableTo Make a Straight RIP CUT Adjusting ClampTo Make a Miter CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTTo Make a Large Panel CUT Accessory Miter Locking Clamps Rail ClampTo Make a Compound Miter CUT Clamp Push Block Bevel To Make NON-THROUGH CutsFeatherboard To Make Dado Cuts Backup Washer MaintenanceGeneral Maintenance LubricationScrews Lock NUT To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop Bolt LockSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps Screw SET Front Rail Miter Locking ClampTo Adjust the Sliding Miter Table Assembly To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BMiter Indicator To Adjust the Miter FenceTo Adjust QUICK-STOP LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage Ryobi 10 in mm Table SAW Model NO. BT3100 Refer to FigureParts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100 Ryobi TECHNOLOGIES, INC