Ryobi SAW BT3100 manual To Make a Compound Miter CUT, To Make a Large Panel CUT

Page 30

OPERATION

■Move the bevel locking lever to the right for angle mode. Turn the blade adjustment handle until the bevel indicator is at the desired angle. Push the bevel locking lever securely to the left to lock the angle.

■Position the rip fence the desired distance from the blade for the cut and lock securely.

■Place a support (the same height as saw table) behind the saw for the cut work.

■Use a push stick to move small pieces of wood past the blade. Never push a small piece of wood into the blade with your hand.

■Stand to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur. Never stand directly in the line of cut.

■Make sure the wood is clear of the blade before turning on the saw.

■Let the blade build up to full speed before feeding the workpiece into the blade.

TO MAKE A COMPOUND MITER CUT

This cut is made with both the miter fence and the blade angled. Set the miter fence and the blade angle with the procedures given earlier.

The miter fence must be on the left side of the blade. It is highly recommended that you test the cut with a piece of scrap wood. Become thoroughly familiar with bevel cross cuts and miter cuts before attempting to perform a com- pound miter cut.

TO MAKE A LARGE PANEL CUT

See Figure 41.

Make sure the saw is properly secured to a work surface so it will not tip over under the weight of a large panel.

WARNING:

Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

■Raise the locking handle on the rip fence to allow the rails to move freely.

■Lift off the sliding miter table assembly by raising the miter locking clamps to release the grippers.

■Remove the accessory table by swinging out the lever and lifting the table up and out.

SLIDING MITER

ACCESSORY

TABLE ASSEMBLY

TABLE

ACCESSORY

TABLE

MITER

LOCKING CLAMPS

RAIL CLAMP

Fig. 41

■Rotate the front rail clamps (under the front rail) to the left and slide the front rail to the side where the panel will rest. Lock the rail clamps after positioning the front rail.

■Rotate the rear rail clamps (under the rear rail) to the left and position the rear rail to support the panel. Align the rear rail with the front rail. Lock the rail clamps after positioning the rear rail.

■Place the accessory table onto the rails far enough from the blade to help support the panel and lock securely.

■Place the sliding miter table assembly onto the rails and lock securely. The miter table can be rotated 180° so the projecting base is at the back of the work surface so you won't run into it as you feed the panel into the blade. (Tables can be placed on either side of blade.)

■Position the rip fence the desired distance from the blade for the cut and securely lock the handle.

■Place a support behind the saw for the cut work.

■Make sure the panel is clear of the blade before turning on the saw.

■Let the blade build up to full speed before feeding the workpiece into the blade.

Page 30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Safety Alert Symbol Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols No Hands SymbolElectrical Connection ElectricalExtension Cords Grounding InstructionsGlossary of Terms In. NUT Driver UnpackingTools Needed Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JSliding FeaturesGetting to Know Your SAW ScalePower Switch Operating ComponentsPrecision Ground MICRO-GRAIN Carbide Teeth Speed and WiringBlades LASER-CUT Body Expansion Slots Blade RotationAssembly Assembling LEG StandTo Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Handwheel To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter Hole BLever To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate FIT LIP of Table Into Rear RailSmall HEX Wrench To Check SAW Blade InstallationTo Install Blade Guard Assembly Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Remove the Blade Inch Blade Guard Riving KnifeRiving Knife Blade Riving Knife Mounting Plate HEX Nuts ShimsTo Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopTo Lock Miter Table Miter Slide Lock Slots for Locking Miter TableTo Make a Straight RIP CUT Adjusting ClampTo Make a Miter CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTAccessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel To Make Dado Cuts Backup Washer MaintenanceGeneral Maintenance LubricationScrews Lock NUT To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop Bolt LockSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps Screw SET Front Rail Miter Locking ClampTo Adjust the Sliding Miter Table Assembly To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BMiter Indicator To Adjust the Miter FenceTo Adjust QUICK-STOP LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage Ryobi 10 in mm Table SAW Model NO. BT3100 Refer to FigureParts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100 Ryobi TECHNOLOGIES, INC
Top Page Image Contents