Ryobi TS1141 manual To Install/replace the Blade, See Figures 16

Page 18

ASSEMBLY

To Install/replace the Blade

See Figures 16 - 17.

WARNING:

A 7-1/4 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from se- curing the blade on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury.

Unplug the saw.

Raise the saw arm.

Rotate lower blade guard up and remove blade bolt cover screw. Rotate blade bolt cover up and back to expose the blade bolt.

Depress the spindle lock button and rotate the blade bolt until the spindle locks.

Using the wrench provided, loosen and remove the blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen.

Remove outer blade washer. Do not remove inner blade washer.

Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 17.

Replace outer blade washer. Double “D” flats on blade washers align with flats on spindle.

Depress spindle lock button and replace blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

Caution:

Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

Tighten blade bolt securely.

Replace the lower blade guard and blade bolt cover.

Replace blade bolt cover screw and tighten securely.

 

Spindle Lock

 

Button

 

Fig. 16

 

NOTE: before use,

 

replace SCREW and

 

tighten SECURELY

 

to prevent guard

 

movement

Blade

 

BOLT

 

cover

 

 

BLADE BOLT

 

COVER

Lower

SCREW

 

blade

 

guard

 

Blade

 

To

 

LOOSEN

 

Blade

Flat(S)

BOLT

on Spindle

 

Inner Blade

 

Washer WITH

To

DOUBLE “D” FLATS

 

Tighten

 

Outer Blade

 

Washer WITH

Fig. 17

DOUBLE “D” FLATS

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Signal MeaningDouble Insulation Cord Length Wire Size A.W.GElectrical Electrical ConnectionGlossary of Terms Blade Wrench FeaturesProduct Specifications Work ClampBevel Lock Knob Know Your Compound Miter SAWAMP Motor Blade Wrench StorageSwitch Trigger Tools NeededSpindle Lock Button Dust BAG Miter saw Head Blade Rear bracket Carrying handleUnpacking AssemblyInstalling the rear bracket/carrying handle Screws Rear bracket Carrying handleMounting the miter saw base to the stand Mounting HolesBase See Figures 10 Indicator Bevel ScrewAssembling the miter saw head to the base UnpackingINSTALLing Batteries in Laser Dust BAGWork Clamp To Cut Your Mark Aligning the laser guide lineRemoving Your Mark To Leave Your MarkTo Install/replace the Blade See Figures 16Squaring the Miter Table to the Fence See Figures 18Squaring the Blade to the Fence See Figures 21Squaring the Blade to THE MITER Table See Figures 25To Cross cut OperationApplications See Figures 29To Bevel Cut IndicatorScaleSCREW indicator Bevel Cut Lock knob See Figures 31To Compound Miter Cut See Figures 33Compound Miter Cut Work Clamp Long Workpiece To Support Long Workpieces45 x 45 Compound Miter CUT SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Number of Sides Left SIDE, Inside Corner Right SIDE, Outside Corner Cutting crown moldingLaying molding flat on the miter table Right SIDE, Inside Corner Left SIDE, Outside CornerCutting warped material See Figures 37Wrong Pivot Adjustments Travel Pivot Adjustment AdjustmentsPositive Stop Adjustments Bevel Pivot AdjustmentTo Adjust the Laser Guide To adjust the miter lock leverLaser adjustment Screw Unlock Miter Lock Lever Brush Replacement MaintenanceGeneral Maintenance LubricationService Model NO. and Serial no
Top Page Image Contents